Filter
Top Products
7. Installing the iPod into the Case
Installing the iPod
Removing the iPod
1.
Align the audio port with the
stereo jack in the case.
1.
Slide the player off
of the stereo jack.
Now the player can
slide straight out of the
case.
2.
Gently snap the player into the
audio jack. Verify the player is
completely plugged into the
audio jack.
NOTE: Do not disturb the T-Seal during removal of the player. If the T-Seal is moved, Please use the
case lid to completely seat the T-Seal.
IMPORTANT: Remove any skins or
covers from your iPod before installing
it into the housing.
Compatible with iPod nano (3
rd
Gen)
6. The T-Seal
DO NOT USE SILICONE GREASE as this will damage the seal.
The removable, black, T-Seal (retained in
the lid), between the base and the lid of
the case is, what keeps your iPod safe and
dry.
Contact Surfaces
T-Seal
IT IS EXTREMELY IMPORTANT YOU ENSURE THE T-SEAL IS PROPERLY
SEATED DURING EACH CLOSURE. If it is out of alignment or twisted you
will cause damage to or destroy your iPod.
Prior to use, verify:
1.
T-Seal is aligned properly in the
Contact Surface of the lid prior
to closure.
2.
T-Seal and contact surface have
been cleaned as necessary using
a soft, lint-free cloth.
3.
T-Seal and Contact Surface are
free of scratches and other
imperfections.
Do NOT use if:
1.
T-Seal is twisted or out of
alignment during closure.
2.
T-Seal and Contact Surfaces
have any dirt, lint, hair, and/or
other debris.
3.
You see scratches or imperfections
on the T-Seal or Contact Surfaces.
To ensure the T-Seal is fully seated in the base of the case, firmly squeeze
both sides (the base and lid) of the case together after each insertion of the
player. Always check to make sure the latch is closed and locked prior to use.
If you have any questions or doubts, please contact H2O Audio Customer Support
iPod nano
T-Seal
Water
Housing
5. Unlocking & Locking the Case
3.
Verify the lid & latch are closed
with the button positioned on the
icon prior to entering the water.
Verify the T-Seal is aligned properly.
1.
Close the lid, and hook the
buckle under the base.
3.
Unhook the buckle from the base.
2.
Pull the latch towards the case
and snap close.
2.
While holding the latch button
towards the unlock icon,
push away from the case to open
the latch.
1.
Slide latch button towards the
unlock icon.
Locking your case
Unlocking your case
3. Introduction
4. Leak Test
The H2O Audio Waterproof Case lets you to listen to digital audio during
active watersports. It houses the Apple iPod nano (3
rd
Gen) digital media
player.
CASE: The H2O Audio case features the LatchTight
TM
Locking System which
keeps the unit waterproof during operation and allows for functional control
of the player while in the water with the Commander
TM
Scroll Wheel.
NOTE: The iPod is NOT waterproof without the H2O Audio case and
Waterproof Headphones and is NOT covered under the product warranty.
Any attempt to use the case with an audio player other than the Apple iPod
nano (3
rd
Gen) will void the Warranty.
HEADPHONES: The case is only waterproof when combined with H2O Audio
waterproof headphones (sold separately). Use of other headphones with a
3.5mm stereo connector will result in a water resistant case, and should not
be submerged.
Before utilizing the system for the first time, it is highly recommended to
perform a 'Leak Test'. Follow the instructions below.
1. Open the case (Section 5), and verify the T-Seal is clean and free of debris.
2. Close the case (Section 5) and attach H2O Audio Waterproof Headphones.
3. Immerse the case, (without the iPod nano 3
rd
Gen) in water and soak for 30 min.
4. Manipulate the Commander
TM
Scroll Wheel during submersion.
5. Remove from the water, dry the exterior. Visually inspect the case for any sign of leaks
before opening.
6. Open the case upside down to prevent water from dropping into the case during
opening.
DO NOT INSTALL THE iPod nano (3
rd
Gen)
INSIDE THE CASE FOR THE LEAK TEST
2. Case Features
IMPORTANT: Make sure the seal is fully seated against the housing base each time you close the
housing. Use the lid to compress the seal into the base if required.
LatchTight Locking
System
TM
SealTight Connector
TM
Commander Scroll
Wheel Control
TM
Lens Clear
Display Window
Compatible with
iPod nano (3
rd
Gen)
H2O Audio cases are designed for specific Apple iPod models, which vary by
generation and storage size. You must ensure the correct case is purchased
for your specific iPod model.
Printed Instructions
Waterproof Case for the
iPod
®
nano (3
rd
Gen)
iN3
h2oaudio.com
Before using this system, please be sure to read, understand, and follow the instructions in this manual.
iN3 - 70 20071106