Filter
Top Products
SM523-G
|
Cup Holder Mount with Flexible Goosneck Shaft with Slim-Grip™ Smartphones
!
Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists™
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in Taiwan & China
© Copyright 2010 Arkon Resources, Inc.
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Friday 9 am - 5 pm, PST
iPhone Holder Attachment
Adjust the angle of the dual T head by tightening the adjustment
nut at the top of the cup holder shaft (A).
Install the iPhone holder to the shaft by inserting the dual T-tabs
(B) on the shaft into the T-slots (C) on on the back of the holder.
Step 1.
Step 2.
Cup Holder Mounting
Connect the gooseneck shaft (A) to the cup holder base (B) by
aligning the groove on the base to the ridge inside of the bottom
of the shaft.
Place the Universal Cup Holder Mount into the designated cup
holder in the vehicle. Adjust the thumb wheel adjuster (C) to open
or close the cup holder prongs to t in the cup holder.
For oversize cup holder openings or the adjustable “pop out” cup
holders use the optional self-adhesive side support pads (D). Install
the pads by removing the adhesive backing and placing it on the
at surface side of the cup holder support leg.
Step 1.
Step 2.
Step 3.
Package Contents:
(1) GN033-SBH - 5” Cup holder mount with exible gooseneck shaft
(1) SM050-2 Universal phone and portable device holder
(1) SP-SM050-LF - Extra Long Support Legs (2 Pack) for larger phones
GN033-SBH
Cup Holder Mount
CLOSE
ON
(B) Cup Holder Base
(A) Cup Holder
Neck
(C) Thumb wheel
adjustment
knob
(D) Optional
support
pads
CLOSE
OPEN
(B) Cup Holder
Shaft T-tabs
(C) T-slots
(A) Angle
Adjustment
Nut
No tools required for installation.
Note: mount may not work with adjustable, “pop out” cup holders or oversize
cup holder openings found in full-size pickup trucks.
A
A
A
A
B
B
Install the Support Legs to the Holder
Step 1.
Insert the holder support legs (A) by sliding them into the
support leg grooves (B) on the top and bottom of the holder.
Do not place mount in or near an air bag deployment zone or where it
will obstruct view of the road.
!
All brand names and product names are trademarks or registered trademarks of their respective owners.
88mm expandable to 138mm
with Extra Long Support Legs
SM050-2 Slim-Grip™
Universal Phone Holder
SP-SM050-LF
Extra Long
Support Legs
(2 Pack)
• Most smartphones, mobile phones, and cell phones
having heights between 80mm and 138mm tall
• Apple iPhone - All models
• RIM BlackBerry - All non-ip models
• HTC Phones - All non-ip models
• Motorola Phones - All non-ip models
• Nokia Mobile Phones - All non-ip models
• Palm - All non-ip models
• LG Mobile Phones - All non-ip models
• Samsung - All non-ip models
• Sony Ericsson - All non-ip models
• Sanyo - All non-ip models
• Pantech - All non-ip models
• Google - All non-ip models
Holder included is Universal, designed to t nearly ALL non-ip mobile phones regardless of whether a
protective case or silicone sleeve is attached to the phone.