Filter
Top Products
less of warranty status.
REQUIREMENTS OF PART 68 - FCC RULES
This device has been granted a registration number by the Federal Communications Commission,
under Part 68 rules and regulations for direct connection to the telephone lines. In order to comply
with these FCC rules, the following instructions must be carefully read and applicable portions fol-
lowed completely:
1. Direct connection to the telephone lines may be made only through the standard modular cord fur-
nished, to the utility installed jack. No connection may be made to party or coin phone lines. On
the bottom of the phone is a label that contains among other information, the FCC Registration
Number and the Ringer Equivalence number (REN) for this equipment. If requested this informa-
tion must be provided to the telephone company. The USOC Jack for this equipment is RJ11C.
2. The telephone company, under certain circumstances, may temporarily discontinue and make
changes in facilities and services which may affect the operation of the users' equipment: however,
the user shall be given adequate notice in writing to allow the user to maintain uninterrupted serv-
ice.
3. In certain circumstances, it may be necessary for the telephone company to request information
from you concerning the equipment which you have connected to your telephone line. Upon
request of the telephone company, provide the FCC registration number and the ringer equiva-
lence number of the equipment which is connected to your line; this information will be found on
the device.
4. If any of your telephone equipment is not operating properly, you should immediately remove it
from the telephone line. It may cause harm to the telephone network.
5. If the telephone company notes a problem, they may temporarily discontinue service. When prac-
tical, they will notify you in advance of disconnection. If advance notice is not feasible, the tele-
phone company must; promptly notify you of such temporary discontinuance; afford the opportuni-
ty to correct the condition; inform you of your rights to bring a complaint to the FCC under their
rules.
6. Repairs to the device may be made only by the manufacturer or an authorized service agency.
This applies at any time during and after warranty. If unauthorized repair is performed, registration,
connection to the telephone lines and remainder of warranty period all become null and void.
7. This equipment is hearing aid compatible.
REQUIREMENTS OF PART 15 - FCC RULES
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction,
may cause harmful interference to radio communications. However, there is not a guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures: -
Move the telephone away from the receiver. -Consult the dealer or an experienced radio/TV techni-
cian for help. Any changes made by the user not approved by the manufacturer can void the user's
authority to operate the telephone.
INDUSTRY OF CANADA REQUIREMENTS
Notice: The Industry Canada label identifies certified equipment. This certification means that the
equipment meets certain telecommunications network protective operational and safety requirements
as prescribed in the appropriate Terminal Equipment Technical Requirements documents. The
department does not guarantee the equipment will operate to the users satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection.
The customer should be aware that compliance with the above conditions may not prevent degrada-
tion of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier.
Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utili-
ty, telephone lines, and internal metallic water pipe systems, if present, are connected together. This
precaustion may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority or electrician, as appropriate. The Ringer Equivalence
Number (REN) of this device is Z.
Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indi-
cation of the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the require-
ment that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. This
telephone connects to the telephone network under the connecting arrangement code CA11A.
FOR CUSTOMER SERVICE CALL
1-800-783-8353
Teledex, LLC
6311 San Ignacio Avenue
San Jose, CA
95119
Telephone: (408) 363-3100
Fax: (408) 363-3136
email: sales@teledex.com
Internet: www.teledex.com
Part Number 605-0320-03A
TELEDEX NUGGET 3 DIAGRAM
DATA PORT
Allows you to connect a facsimile machine,
modem, or answering machine to the tele-
phone line.
HANDSET VOLUME KEY
Changes handset volume by
pressing repeatedly.
REDIAL KEY
To automatically redial
last number dialed
MESSAGE WAITING LIGHT (optional)
Signals that a message is waiting for retrieval.
See your system administrator for instructions
on retrieving messages.
HEARING AID
COMPATIBLE HANDSET
DIAL KEYS (DTMF PAD)
For dialing phone numbers.
FLASH KEY
For programming of FLASH duration.
See instructions for programming details.
STORE KEY (hidden)
Used in programming of number sequences.
See instructions for programming details.
AUTO DIAL KEYS 1-3
For easy, one-touch dialing of guest services or
PBX features. Programmed during installation.
HANDSET WALL MOUNT
RETAINING CLIP
Allows handset to stay on hook when used
in wall mount configurations.
HANDSET HOLDER
Used to temporarily hold the handset,
without hanging up the telephone,
when telephone is wall mounted.
RING VOLUME
Adjusts the ringer volume
to LOW or HI settings.
HANDSET JACK
Modular jack that connects coiled Handset
Cord from the Telephone to the Handset.