Blomberg International WNF 7201 WE20 Manual

A SERVICE OF

next previous

13

EN

the programme will turn on.

C

 Ifnoprogrammeisstartedornokeyis

pressed within 1 minute during programme

selection process, the machine will switch to

Pause mode and the illumination level of the

temperature, speed and loading door indicator

lightswilldecrease.Otherindicatorlightsand

indicatorswillturnoff.OncetheProgramme

Selectionknobisrotatedoranybuttonis

pressed, indicator lights and indicators will turn

on again.

Child Lock

Usechildlockfunctiontopreventchildrenfrom

tampering with the machine. Thus you can avoid

any changes in a running programme.

C

 IftheProgrammeSelectionknobisrotated

when the child lock is active, the lights on the

1

st

and 2

nd

auxiliaryfunctionbuttonswillblink

3 times. The child lock does not allow any

change in the programmes and the selected

temperature, speed and auxiliary functions.

C

Even if another programme is selected with

theProgrammeSelectionknobwhiletheChild

Lock is active, previously selected programme

will continue running.

C

When the Child Lock is active and the

machine is running, you can switch the

machine to Pause mode without deactivating

theChildLockbyturningtheProgramme

SelectionknobtoOn/Offposition.When

youturntheProgrammeSelectionknob

afterwards, the programme will resume.

To activate the Child Lock:

Press and hold 1

st

and 2

nd

Auxiliary Function

buttonsfor3seconds.Thelightsonthe1

st

and 2

nd

AuxiliaryFunctionbuttonswillflashwhileyoukeep

thebuttonspressedfor3seconds.

To deactivate the Child Lock:

Press and hold 1

st

and 2

nd

auxiliaryfunctionbuttons

for 3 seconds while any programme is running. The

lights on the 1

st

and 2

nd

AuxiliaryFunctionbuttons

willflashwhileyoukeepthebuttonspressedfor3

seconds.

C

 Inadditiontothemethodabove,todeactivate

the Child Lock, switch the Programme

SelectionknobtoOn/Offpositionwhenno

programme is running, and select another

programme.

C

When the power is restored after a power

failure or after your machine is unplugged

and plugged in again, the Child Lock will not

bedeactivatedwhenthemachineresumes

operating.

Progress of programme

Progressofarunningprogrammecanbefollowed

fromtheProgrammeFollow-upindicator.Atthe

beginningofeveryprogrammestep,therelevant

indicator light will turn on and light of the completed

step will turn off.

You can change the auxiliary functions, speed

and temperature settings without stopping the

programme flow while the programme is running.

To do this, the change you are going to make must

beinastepaftertherunningprogrammestep.If

thechangeisnotcompatible,relevantlightswill

flash for 3 times.

C

 Ifthemachinedoesnotpasstothespinning

step,RinseHoldfunctionmightbeactive

ortheautomaticunbalancedloaddetection

systemmightbeactivatedduetothe

unbalanceddistributionofthelaundryinthe

machine.

Loading door lock

There is a locking system on the loading door of

the machine that prevents opening of the door in

caseswhenthewaterlevelisunsuitable.

Loading door light will start flashing when the

machine is switched to Pause mode. Machine

checksthelevelofthewaterinside.Ifthelevelis

suitable,LoadingDoorlightilluminatessteadily

within1-2minutesandtheloadingdoorcanbe

opened.

Ifthelevelisunsuitable,LoadingDoorlightturns

offandtheloadingdoorcannotbeopened.If

youareobligedtoopentheLoadingDoorwhile

theLoadingDoorlightisoff,youhavetocancel

the current programme; see "Canceling the

programme".

Changing the selections after

programme has started

Switching the machine to pause mode

PresstheStart/Pausebuttontoswitchthe

machine to pause mode while a programme is

running. The light of the step which the machine

isinstartsflashingintheProgrammeFollow-up

indicatortoshowthatthemachinehasbeen

switched to the pause mode.

Also,whentheloadingdoorisreadytobeopened,

LoadingDoorlightwillalsoilluminatecontinuously

in addition to the programme step light.

Changing the speed and temperature

settings for auxiliary functions

Dependingonthesteptheprogrammehas

reached, you may cancel or activate the auxiliary

functions; see, "Auxiliary function selection".

You may also change the speed and temperature

settings; see, "Spin speed selection" and

"Temperature selection".

C

 Ifnochangeisallowed,therelevantlightwill

flash for 3 times.

Adding or taking out laundry

PresstheStart/Pausebuttontoswitchthe

machinetopausemode.Theprogrammefollow-

up light of the relevant step during which the

machine was switched into the pause mode will

flash.

WaituntiltheLoadingDoorcanbeopened.Open

theLoadingDoorandaddortakeoutthelaundry.

ClosetheLoadingDoor.Makechangesinauxiliary

functions, temperature and speed settings if

necessary.PressStart/Pausebuttontostartthe

machine.

Canceling the programme

To cancel the programme, turn the Programme

Selectionknobtoselectanotherprogramme.

Previousprogrammewillbecanceled.End/