16
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 0720-31-8111 Fax: 0720-33-5222
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramesy, N.J. 07446, U.S.A.
Tel: 201-825-7950 Fax: 201-825-8150 E-mail: onkyo@onkyousa.com
ONKYO EUROPE ELECTRONICS GmbH
Industriestrasse 20, 82110 Germering, GERMANY
Tel: 089 84 93 20 Fax: 089 84 93 226 E-mail: info@onkyo.de
ONKYO CHINA LIMITED
Units 2102-7, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852 2429 3118 Fax: 852 2428 9039
E
http://www.onkyo.co.jp/
HOMEPAGE
SN 29342785
I9905-1
Troubleshooting Guide
• No power.
Cause: Power cable is not properly plugged into the AC outlet.
Remedy: Insert the power plug firmly.
• A disc is loaded in the disc tray, but playback will not start.
Cause: A disc in the disc tray may be upside down.
Remedy: Load the disc with the label facing upward.
Cause: The disc is dirty.
Remedy: Clean the disc.
Cause: Moisture has accumulated inside the CD changer.
Remedy: Remove the disc from the disc tray, place the CD
changer in a warm place, and leave the power on for
about one hour.
• No sound is heard.
Cause: Connections may be incomplete or incorrect.
Remedy: Check all cable connections. Insert all the plugs firmly
into the jacks.
Cause: The input selector switch on the amplifier may be set incor-
rectly.
Remedy: Set the switch to the proper position. See your ampli-
fier’s operating instructions for more information.
• Disc playback skips.
Cause: The disc is dirty.
Remedy: Clean the disc.
Cause: A disc is scratched.
Remedy: Replace the disc.
Cause: The CD changer is subject to being accidentally bumped.
Remedy: Place the CD changer in a more stable location.
• Search time (when locating a specific track) is extremely
long.
Cause: The disc is dirty.
Remedy: Clean the disc.
Cause: The disc is scratched.
Remedy: Replace the disc.
• Track numbers cannot be stored in memory.
Cause: No disc in the tray.
Remedy: Load a disc in the tray.
Cause: You have entered a track number that does not exist on the
disc.
Remedy: Use only the track numbers that exist on the disc.
• Front panel controls function correctly, but remote control-
ler does not.
Cause: No batteries in remote controller.
Remedy: Insert batteries.
Cause: Batteries have worn out.
Remedy: Replace batteries.
Because the unit contains a microcomputer to provide advanced
functions, it may malfunction due to external noise or static elec-
tricity. If this happens, press the POWER switch on the unit and
then press it in again after about five seconds.
Specifications
Signal readout system: Optical non-contact
Reading rotation: About 500 - 200 r.p.m.
(constant linear velocity)
Linear velocity: 1.2 - 1.4 m/s
Error correction system: Cross Interleave Reed-Solomon code
D/A converter: 1 bit PWM/ACCUPULSE
Sampling frequency: 352.8 kHz (8 times oversampling)
Number of channels: 2 (stereo)
Frequency response: 5 Hz - 20 kHz
Total harmonic distortion: 0.005% (at 1 kHz)
Dynamic range: 96 dB
Signal to noise ratio: 92 dB
Channel separation: 92 dB (at 1 kHz)
Wow and Flutter: Below threshold of measurability
Output level: 2 volts r.m.s.
Power consumption: 10 watts
Power supply: AC 120 V, 60 Hz
Dimensions (W × H × D): 435 × 131 × 433mm
(17-1/8" × 5-3/16" × 17-1/16")
Weight: 6.9 kg (15.2 lbs.)
Specifications and features are subject to change without notice.
