7 7 7 7 7 77 7 7 7 7 7 7
1 1 1 1 1 11 1 1 1 1 1 19 9 9 9 9 99 9 9 9 9 9 9
3 3 3 3 3 33 3 3 3 3 3 3
10 10 10 10 10 1010 10 10 10 10 10 10
4 4 4 4 4 44 4 4 4 4 4 46 6 6 6 6 66 6 6 6 6 6 6
0 0 0 0 0 00 0 0 0
0 0 0
5 5 5 5 5 55 5 5 5 5 5 5
8 8 8 8 8 88 8 8 8 8 8 8
2 2 2 2 2 22 2 2 2 2 2 2
1
P
OWER
0
I
NPUT
BASS
CLEAN
TREBLE
GAIN GAIN
DRIVE1DRIVE2
S
COOPBRIGHT SCOOP
VOLUME VOLUME
BASS
MIDDLE TREBLE
CLEAN
REVERB
DRIVE
REVERB
VIBE
MIDDLE
VOLUME
CLEAN CHANNEL
DRIVE 1
D
RIVE 2DRIVE EQ REVERB
T
U
B
E
F
U
S
I
O
N
22
POWER:
HEADPHONES:
EXTENSION SPEAKER SOCKET
FX RETURN :
FX SEND :
Socket for connecting external power source.
Socket provided for connecting pair of quality headphones. When headphones are connected to
the amplifier the output from the on board speaker is muted.
Socket provided for connecting the output of an external effects device.
Socket provided for connecting an external effects device. The output from this socket should be
connected to the external effect devices input.
FOOTSWITCH SOCKET:
:
Socket provided for connecting the supplied TF footswitch. TheTF footswitch is a
dedicated footswitch forTF amplifiers please do not attempt to connect anything other than theTF footswitch supplied
as this may result in serious damage to your amplifier.
Socket provided for connecting an external speaker enclosure. NOTE The
minimum impedance of any speaker cabinet connected to you amplifier must not be less than 8 Ohms. Connecting a
load of less than 8 Ohms will result in your amplifier overheating. Whilst this is not a problem in the short term,
prolonged use in this manner will result in permanent damage to your amplifier and voiding of your amplifiers guarantee.
16
Eng
Laney
OPERATING INSTRUCTIONS
Tube Fusion -II
17
2
3
4
6
7
8
9
10
11
12
13
14
24
25
27
1
5
15
23
16
23
24
27
17
Designed in the UK by BLT Industries LTD.
N1646N1646
MAXIMUM POWER CONSUMPTION
120 WATTS ~50/60 HZ
WARNING-THIS EQUIPMENT MUST BE EARTHED.
WARNING-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS APPLIANCETO RAIN OR MOISTURE
.
CAUTION -TO REDUCE THE RISK OF ELECTRICSHOCK DO NOT
REMOVECOVERS
.NO USER SERVICEABLEPARTS INSIDE.REFER
SERVICINGTO QUALIFIED PERSONNEL ONLY
.
ATTENTION -REMPLACER LE FUSIBLE SEULEMENT PARLE MEME
TYPE ET LE MEME CALIBRE
.
ATTENTION -DEBRANCHER LE CORDOND ALIMENTATION
AVANT TOUTE INTERVENTION
.
,
A
VIS -RISQUE DE CHOC ELECTRIQUE -NE PAS OUVRIR.
CAUTION -FOR CONTINUED PROTECTIONAGAINST RISK OF FIRE
REPLACEONLY WITH SAME TYPE AND RATEDFUSE
.
T2A L 115V
T1A L 230V
~
~
T2A L 115V
T1A
L 230V
~
~
F
USE
R
ATING
&S
UPPLY
V
OLTAGE
.
!
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
Serial Number
FX Return
FX Send
Head Phones
Extension
Loudspeaker
8 OHM
MINIMUM IMPEDANCE
Footswitch
Use With Dedicated
TF3 Way Footswitch only.
Laney
MADE IN CHINA
19
20
21
26
18
22
VIBE:
CLEAN REVERB LEVEL:
DRIVE REVERB LEVEL:
CLEAN CHANNEL SWITCH:
DRIVE 1 CHANNEL SWITCH:
DRIVE 2 CHANNEL SWITCH:
Generates a radical EQ cut and boost. Difficult to explain but easy to hear! Give it a try. Works on both
channels.
Sets the overall level of REVERB present in the clean channel signal.
Sets the overall level of REVERB present in the drive channel signal.
Selects the amplifiers CLEAN channel.
Selects the amplifiers DRIVE 1 channel.
Selects the amplifiers DRIVE 2 channel.
18
19
20
21
25
26
TF200-II Rear Panel
TF200-II Front Panel
Page 4
