-
We recommend using a dedicated circuit for this appli-
ance to prevent electrical overload.
-
Follow all Federal, State and local electrical, fire and
building codes and ordinances when installing the
receptacle and / or the appliance.
-
In some communities, a wall switch is required to turn
power to the appliance ON and OFF.
-
To reduce the risk of fire, electric shock, or personal
injury, installation work and electrical wiring must be
done by a qualified electrician in accordance with all
applicable codes and standards, including fire-rated
construction.
-
The Power Plug must be easily accessible so that the
appliance can be disconnected from the mains quickly
in an emergency. It must not be behind the back of the
appliance.
-
The top of the electric outlet must be located within
82-5/8 in. (2100 mm) from the top of the base in the
cabinet.
4.5 Switching on the appliance
Switch on the appliance 2 hours before loading
with frozen food for the first time.
Do not load frozen foods until the temperature
display reads 0 °F (-18 °C).
u
Open the door.
u
Press On/Off button
Fig. 2 (8)
.
w
The temperature display and the Alarm symbol will
flash until the temperature is cold enough. If the
temperature is greater than 32 °F (0 °C), flashing
dashes will appear; if the temperature is lower than this,
the current temperature will flash on the display.
w
The interior light comes on when the door is opened.
w
Whenever “DEMO” appears on the display, the appli-
ance is running in demonstration mode. Contact the
customer service department.
5 Operation
5.1 Temperature display unit
The temperature display can be changed from °F to °C.
5.1.1 To change the unit
u
Activate setting mode: Press SuperFrost button
Fig. 2 (9)
for about 5 seconds.
w
S is displayed in the temperature display.
w
The Menu symbol
Fig. 2 (3)
lights up.
u
Using Up button
Fig. 2 (1)
/ Down button
Fig. 2 (2)
select °.
u
To confirm: Briefly press SuperFrost button
Fig. 2 (9)
.
u
Using Up button
Fig. 2 (1)
/ Down button
Fig. 2 (2)
select °F or °C.
u
To confirm: Briefly press SuperFrost button
Fig. 2 (9)
.
u
To exit setting mode: Press On/Off button
Fig. 2 (8)
.
-or-
u
Wait 5 minutes.
w
The temperature is again displayed in the temperature
display.
5.2 Brightness of the temperature
display
You can adapt the brightness of the temperature display
to the light conditions in the room in which it is installed.
If the door is open or the control panel is used the temper-
ature indicator lights up at maximum brightness. About 1
minute after the door is closed or no button has been
pressed on the control panel, the temperature display
goes back to the set brightness.
5.2.1 Setting the brightness
The brightness can be set between h0 (minimum lumi-
nosity) and h5 (maximum luminosity).
u
To activate setting mode: Press SuperFrost button
Fig. 2 (9)
for about 5 seconds.
w
S is shown on the display.
w
The Menu symbol
Fig. 2 (3)
lights up.
u
Using Up button
Fig. 2 (1)
or Down button
Fig. 2 (2)
select h.
u
To confirm: Briefly press SuperFrost button
Fig. 2 (9)
.
u
To set the display brighter: Press Up button
Fig. 2 (1)
.
u
To set the display darker: Press Down button
Fig. 2 (2)
.
u
To confirm: Press SuperFrost button
Fig. 2 (9)
.
w
The brightness is set to the new value.
u
To deactivate setting mode: Press On/Off button
Fig. 2 (8)
.
-or-
u
Wait 5 minutes.
w
The temperature is again displayed in the temperature
display.
5.3 Child-proof lock
You can use the child-proof lock to lock the
buttons. This means that children cannot acci-
dentally switch off the appliance when playing.
5.3.1 Switching on the child-proof lock
u
Activate setting mode: press and hold the SuperFrost
button
Fig. 2 (9)
for approximately 5 s.
w
S is shown on the display.
w
The Menu symbol
Fig. 2 (3)
lights up.
u
Using the Up button
Fig. 2 (1)
or Down button
Fig. 2 (2)
,
select c.
u
Press the SuperFrost button
Fig. 2 (9)
briefly to confirm.
When
c1 is shown on the display:
u
To switch on the child-proof lock, press the
SuperFrost button
Fig. 2 (9)
briefly.
Operation
* Depending on model and options 7
