22
ENGLISH
ADVANCED CONNECTING
R
SR
C
SW
SBR
MULTI.
OUT
SL
SBL
L
R
L
(
AUX2
)
7.1CH INPUT
L
SL
C
SBL
R
SR
SW
SBR
RS-232C
SPEAKER C
OFF
ON
R
L
FM
(
75
)
GND
AM
ANTENNA
V
DVD
TV
IN
TV
DVD
VCR IN
S-VIDEO
VIDEO
PRE OUT
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
FRONT
B
(
AUX2
)
7.1CH INPUT
L
SL
C
SBL
R
SR
SW
SBR
R
L
R
SR
C
SW
SBR
SL
SBL
L
PRE OUT
L
R
FRONT SURR.
SURR.
BACK
SUB
WOOFER
CENTER
RL
LR
R L
LR
R L R L
L
R
FRONT SURR.
SURR.
BACK
SUB
WOOFER
CENTER
R L R L R L
RL RL
LR
Power
Amplifer
DVD Audio player
or
Super Audio CD Multi
channel player
Center
Front
Left
Front
Right
Surround
Left
Surround
Right
Subwoofer
Surround
Back Left
Surround
Back Right
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio
source such as a Super Audio CD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page 31.
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifi ers.
Be sure to connect each speaker to the corresponding
external power amplifi er.
CONNECTING THE REMOTE CONTROL JACKS
q
You can control other Marantz products through this
unit with the remote controller by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
signal only to the unit. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er’s, power
switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the
back of other units (not the SR4002/SR5002) to
“EXT”.(EXTERNAL) to use this feature.
R
R
L
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
DIGITAL IN
OUT
IN
CD/CDR
OUT
IN
TAPE
VCR
VD
AUDIO
DSS
IN
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
VD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
AC IN
MODE
FLASHER
IN
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
CENTER.
FRONT A OR B.CENTER.
FRONT A
+
: 8 OHMS
SPEAKER
SYSTEMS
B
FRONT
A
SURR.SURR BACK : 6-8 OHMS
SURR.SURR BACK : 6-8 OHMS
2
1
5
4
DC
TRIGGER
3
INPUT
3
INPUT 1
COMPONENT
VIDEO
IN
OUT
REMOTE CONT.
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
1
RC OUT
2
DVD playerCD recorder CD player
OPTION
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the unit, be sure
to always disable operation of the infrared sensor on
the unit by using the following procedure.
1.
Hold down the 7.1CH INPUT (SR4002) / MULTI
(SR5002) button and MENU button on the front
panel at the same time for fi ve seconds.
2.
The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3.
Press the 1 or 2 cursor button to change this to
“IR=DISABLE”.
4.
Press the ENTER button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note:
Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not connected.
Otherwise, the unit will be unable to receive remote
control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
