1
Getting Started Section 1
1-A Accessories 1-B Location of Controls
1-C Settings
∑ AC Adaptor. . . . . . . . . . . . . . . . . one
∑
Order No.
PQLV19Z
(PQLV19)
∑ Telephone Line Cord . . . . . . . . . one
∑ Order No.
PQJA10075Z
∑ Battery . . . . . . . . . . . . . . . . . . . . one
∑ Order No.
N4HHEPA00001
(HHR-P513)
∑ Handset Cover . . . . . . . . . . . . . . one
∑ Order No.
PQKK10136Z2
∑ Belt Clip . . . . . . . . . . . . . . . . . . . one
∑
Order No.
PQKE10361Z2
∑ Shoulder Rest Attachment . . . . . one
∑ Order No.
PQKE10364Z1
≥For extra orders, call 1-800-332-5368.
3
Charge the battery for about 6 hours.
≥See section 4-A for more
details.
≥The CHARGE indicator
lights and the unit beeps
once.
≥It is normal for the back
on the handset to feel
warm during battery
charge.
Handset Base unit
≥USE ONLY WITH Panasonic AC ADAPTOR PQLV19 (Order No.
PQLV19Z).
≥The AC adaptor must remain connected at all times. (It is normal
for the adaptor to feel warm during use.)
≥The unit will not work during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To select the dialing mode TONE (preset) or PULSE
You can program the dialing mode using the handset near the
base unit. Make sure the unit is not being used and the
handset is lifted off the base unit before programming.
While pressing [FLASH/CALL WAIT]:
Press and hold [#] (PULSE) until the unit beeps.
OR
Press and hold [](TONE) until the unit beeps.
≥If 3 beeps sound during programming, walk closer to the base
unit and start again from the beginning.
1
Connect as shown.
Power Outlet
(AC 120 V, 60 Hz)
AC
Adaptor
Telephone
Line Cord
Single-Line Telephone Jack (RJ11C)
Fasten the AC
adaptor cord.
Hooks
CHARGE Indicator (1-C)
[HANDSET LOCATOR] (3-B)
Charge
Contacts (4-A)
IN USE Indicator (2-B, 3-B)
Antenna (4-F)
[SP-PHONE]
(Speakerphone/
Channel) (2-A)
[ ] (TALK/Channel) (2-A)
[REDIAL] (2-A)
[OFF] (2-A)
VOL. (VOLUME) Key
([
▲], [▼]) (2-A, 2-B)
[VOICE ENHANCER]
and Indicator (2-A)
Talk/Ringer Indicator
(2-A, 2-B)
Microphone (2-A)
RECHARGE
Indicator (4-A)
Receiver
Headset Jack (4-D)
[FLASH/CALL WAIT] (3-D)
Antenna
Charge Contacts (4-A)
Speaker
Back side
Ringer
Indicator (2-B)
[ ] (TONE) (3-C)
2
Insert the battery (1), and press it down until it
snaps into the compartment (2).
Close the cover.
For assistance, please call: 1-800-211-PANA(7262)
CHARGE indicator
OR
To replace the battery:
Press the notch on the cover firmly and
slide it as indicated by the arrow.
Replace the old battery with a new one
(4-A). Close the cover and charge the
battery for about 6 hours.
