4
•
REVO PLATINUM EDITION
This model requires the installation of a radio system. The receiver box
is designed to fit most standard size “mini” or “micro” receivers (actual
dimensions of box are 32mm wide x 45mm long x 26mm tall [1.26" x 1.77"
x 1.02"]). A rechargeable 5-cell nickel metal hydride (NiMH) battery pack is
include to power your radio system.
1.
Remove the lid from the radio box.
2.
Plug each steering servo into each of the channel 1 ports on the
receiver (for receivers with only one channel 1 port, use the included
Y-harness to plug both steering servos into the channel 1 port on
the receiver).
3.
Plug the throttle servo into the channel 2 port on the receiver.
4.
Plug the red battery plug from the on/off switch into the battery
port on the receiver.
5.
Leave the extra male
plug (black) from the
on/off switch loose
inside the receiver box.
This is the charge plug
and will need to be
used for charging the
receiver battery pack.
6.
Make sure the battery
pack is plugged into the female plug (red) of the on/off switch.
7.
For receivers using crystals, make sure that the transmitter and
receiver crystals are on matching frequencies.
8.
Route the receiver antenna through the radio box lid and then slide
the antenna wire through the antenna tube.
9.
Use the supplied self-adhesive
foam (located in your owner’s
manual package) to cushion
the receiver. Remove the
adhesive backing strip and
attach the foam to either the
bottom of the receiver or to the
shelf inside the radio box (A).
10.
Secure the lid to the radio box
with a body clip and then slide
an antenna cap over the end of
the antenna tube while leaving
the antenna wire exposed.
11.
Insert the antenna tube into
the mounting post. Slide the
crimp nut over the antenna
tube and screw it onto the
antenna post. Use the supplied
tool to tighten the crimp nut on
the post just until the antenna
tube is securely in place (B). Do not over tighten.
12
. Refer to your radio/receiver owner’s manual for proper radio set up
and operation.
CHARGING THE RECEIVER BATTERY
Your Revo is equipped with the RX Power Pack, a rechargeable 5-cell
nickel metal hydride (NiMH) battery pack. The RX Power Pack must be
fully charged before running the truck. Revo has a charging jack located
inside the receiver box so you do not have to remove the battery pack
from the model. To charge the battery, remove the receiver box cover
and plug the charger output cord into the charging jack. The on/off
switch must be in the off position to charge the receiver pack. Caution!
Never charge batteries in an enclosed car interior or while driving. Never
leave charging batteries unattended. Monitor them closely.
BATTERY CARE
Some precautions should be taken to maintain the performance of the
rechargeable NiMH receiver pack in your model. Improper use of the
battery pack could result in personal injury or damage to your truck.
•
Only use approved chargers for NiMH battery packs (such as the Traxxas
TRX Power Charger, part #3030X). Do not exceed the maximum charge
rate of 1 amp.
•
Do not short-circuit the battery pack. This may cause burns and severe
damage to the battery pack.
•
Do not burn or puncture the batteries. Toxic materials could be released. If
eye or skin contact occurs, flush with water.
•
Store the battery pack in a dry location, away from heat sources
and direct sunlight.
•
Nickel Metal Hydride batteries must be recycled or disposed of properly.
•
Do not completely discharge the RX Power Pack or you could damage
it. Do not use dischargers on the pack. Store the battery with at
least 25% charge. Stop running and recharge at the first indication
of reduced voltage.
Battery
Steering
Servos
Throttle
Servo
RX Power Pack
5-cell NiMH
Battery
Charging
Jack
On/Off
Switch
Antenna
Receiver
(not included)
“Y” harness
Channel 2
Channel 1
Channel 1*
* Traxxas receiver #2216 shown has two Channel 1
outputs. Use the included “Y” harness for
receivers with one Channel 1 output.
Typical Radio System Wiring
Charging Jack
RADIO INSTALLATION AND BATTERY CARE
The optional Traxxas TRX Power Charger can
be purchased separately to charge the RX
Power Pack. The TRX Power Charger (Part
#3030X) is a peak-detecting unit that will charge
the RX Power Pack in about one hour. The
peak detection circuitry automatically shuts off
the charger when the maximum charge has been
achieved. The TRX Power Charger can operate on
either AC or DC power.
The optional DC car adapter (Part #3032) features a tangle-free,
extra long wire and integrated fuse. The long charging cord
allows the model to remain outside the car while charging.
Sold
Separately
Sold
Separately
A B
5304 Manual Work.indd 4 3/12/08 7:47:14 PM
