6
UNASSEMBLED PARTS
PRODUCT SPECIFICATIONS
Gasoline Capacity
1.5 qt.
and Type: Unleaded Regular
Oil Type SAE 30 (above 32°F)
(API-SG-SL): SAE 5W-30(below 32°F)
Oil Capacity: 20 oz.
Spark Plug: Champion RC12YC
(Gap: .030")
Ground Speed Forward: 0-4 mph
Reverse: 0-1 mph
Blade Bolt Torque: 45-55 Ft. Lbs.
3TEERINGª7HEELª)NSERT
3TEERINGª7HEEL
3EAT
3TEERINGª#OVER
3TEERINGª
3HAFTª#OVER
3TEERINGª3HAFTª
ª,ARGEª&LATª7ASHER
ªª*AMª.UT
ªª,OCKª.UT
ªªXªªª
(EXª"OLT
ª0IN
ªª&LATª7ASHER
3LOPEª3HEET
ª+NOB
ª+EY
ª7ASHER
3TEERINGª7HEELª!DAPTER
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in main tain ing,
caring for and using your riding mower.
• Follow the instructions under “Main te-
nance” and “Stor age” sec tions of this
manual.
• Wear proper Personal Protective Equip-
ment (PPE) while operating this machine,
including (at a minimum) sturdy footwear,
eye protection, and hearing protection.
Do not mow in shorts and/or open toed
footwear.
• Always let someone know you are outside
mowing.
WARNING: This riding mower is
equipped with an internal com bus tion en-
gine and should not be used on or near any
un im proved forest-covered, brush-covered
or grass-cov ered land unless the engine’s
exhaust system is equipped with a spark
arrester meeting applicable local or state
laws (if any). If a spark arrester is used, it
should be maintained in effective working
order by the operator.
In the state of California the above is required
by law (Section 4442 of the California Public
Resources Code). Other states may have
similar laws. Federal laws apply on federal
lands. A spark arrester for the muffler is
available through your nearest authorized
service center.
35
RIDING MOWER - -CATALOG NO. WE261
STEERING
1 532 43 65-00 WHEEL ASM (FRONT)
2 812 00 00-01 E-CLIP
3 532 18 89-67 WASHER, HARDENED
4 532 12 17-49 WASHER, 1/4 X 3/4
5 532 43 53-24 SPINDLE, RH
6 532 12 49-31 WASHER, HARDENED THRUST
7 532 12 49-37 BUSHING, STEERING COLUMN
8 532 42 10-76 PIN, 5/64 X 3/4 COTTER
9 819 13 14-14 WASHER
10 532 42 80-57 WELDMENT, LWR STRG SHAFT
11 532 42 80-35 LINK, STRNG LH
12 532 42 80-36 LINK, STRNG RH
13 874 78 05-24 BOLT, 5/16-18 X 1 1/2
14 819 13 10-16 WASHER
15 873 80 05-00 NUT, 5/16-18
16 532 42 80-44 BUSHING, STEERING SNAP
17 532 42 82-52 SUPPORT, UPPER STEERING
18 532 19 52-27 BUSHING, UPPER STEERING
19 817 00 05-12 BOLT, 5/16-18 X 3/4
20 532 42 80-45 CLIP, RETAINER SPRING
21 532 42 83-47 COVER, STEERING COLUMN
22 532 42 80-38 SHAFT, STEERING
23 532 43 77-47 ADAPTER, STEERING WHEEL
24 819 18 38-12 WASHER, 9/16 X 2 3/8 12 GA.
25 873 94 08-00 NUT, JAM LOCK 1/2-20
26 532 44 16-14 WHEEL, STEERING
27 532 44 16-15 CAP, STEERING WHEEL
28 532 19 98-49 CLIP, RETAINER SPRING
29 532 43 53-23 SPINDLE, LH
30 532 43 64-99 CAP, HUB, AXLE
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
