ClearOne comm 600/900 Cell Phone User Manual


 
Using the RAV — Using the Controller
53
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Using the RAV — Using the Controller
52
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Managing Calls
Most phone specific functions,such as dialing a call or adding a phonebook entry,will be
managed from the RF controller.Phonebook and dialer actions can be done through Rav-
Ware as well.See page 43 for more information.
Using the Controller
To answer a call
Press on the RF controller to answer
the call.When there is an incoming call,
the phone rings and the LEDs on the
microphones flash.
Note: RAV can also be set to
automatically answer calls.See page 56 to
enable Auto-Answer.
To make a call
1. Press .You will hear a dial tone.
2. Dial the number as you would on a
standard phone.The number appears on
the LCD screen.
Note
:The controller accepts a maximum
of 44 characters. No more than 44
characters can be entered.
18005781234
Figure 4.1.LCD screen
To pre-dial a call
1. Dial a phone number.
You can press to delete the last digit
entered in the pre-dialing string.
2. Press to send the call.
Note
: The phonebook key will delete the
entire dial string if you press it for two
seconds. Pressing and holding the pound
(#) key for two seconds will insert a pause
into the dialing string.The duration of the
pause is two seconds.
To use speed dial
Press and hold the assigned speed dial
number on the dial pad.
Note
: You can dial numbers 1-9 by
pressing and holding the assigned number.
To dial speed dial 10, press and hold 0.
To redial a phone number
Press .
Note
: REDIAL saves the last number that
was dialed from the controller. Once
REDIAL is pressed,the phone will be taken
off-hook and the number will be dialed.
To dial a call from the Phonebook
1. Press on the RF Controller.
2. Scroll to the entry and press .
Conference
Sales Team
Product Management
*
Figure 4.2.Dialing from the phonebook
To use the status key
Press and hold for two seconds to
display the status of the RAV.
If the phone is not in use (on-hook) the
LCD will display the device name,the date
and time and the local number.
If the phone is in use (off-hook),the LCD
will display the call duration,the date and
time and the dialed number.
To send a flash signal
Press to use call transfer,call waiting
or conference calling.
Note
:This feature is dependent on your
PBX service or local phone service.Refer
to your PBX vendor or local telephone
service for details.
To adjust the speaker volume
Press to increase the volume.
– Or –
Press to decrease the volume.
Note
:If an external amplifier is dragged
to the line output or record devices in
RAV-Ware, the volume buttons will be
programmed to adjust the external
amplifier. See page 37 for more
information.
To end a call
Press to disconnect the call.
Note
:RAV can also be set to
automatically disconnect calls. See page
57 to enable Auto-Disconnect.
To mute/unmute microphones
1. Press to mute the microphones.The
microphone LEDS will illuminate red.
2. Press again to unmute microphones.
The microphone LEDS will illuminate
green.
Note:This function mutes all microphones
in the room.The microphone LEDs and the
mixer front panel LEDs light red when the
microphones are muted.
ClearOne 55
10/13/04 14:33 PM
8013568518
11:14
10/13/04 14:33 PM
9795311468
Figure 4.3.On-hook status
Figure 4.4.Off-hook status