the appliance has not been used for 3 weeks, you should
replace the lter:
1. Remove the exhausted lter;
2. Remove the new lter from the packaging.
3. Turn the date indicator disk (see g. 33) until the next 2
months of use are displayed (the lter lasts about two
months);
4. Rell the tank;
5. Insert the lter in the water tank and immerse it
completely, tilting it to enable the air bubbles to escape
(g. 34);
6. Place the lter in the lter housing (g. 35aa) and press as
far as it will go. close the tank with the lid (g. 35b), then
replace the tank in the machine;
7. Position a container with a minimum capacity of 3.4 oz /
100 ml under the hot water spout.
8. Press the MENU/ESC button to enter the menu;
9. Press the MILK or CAPPUCCINO button until “Reset lter
“ is displayed.
10. Press the button;
11. The message “Conrm?” is displayed.
12. Press the button to conrm the selection;
13. “Hot water, Press OK” is displayed.
14. Press the button to conrm the selection. the
appliance begins delivering hot water and the message
“Please wait “ is displayed.
15. After delivery, the appliance returns automatically to the
“ready for coee” position.
The new lter is now active and you can use the coee maker.
Removing the lter
If you want to continue using the appliance without a lter,
you must remove it and notify the appliance of its removal as
follows:
1. Extract the tank and exhausted lter;
2. Press the MENU/ESC button to enter the menu;
3. Press the MILK or CAPPUCCINO button (g. 8) until
“Install lter Enabled” is displayed;
4. Press the button
5. “Disable?” is displayed;
6. Press the button to conrm and the MENU/ESC
button to exit the menu.
TECHNICAL SPECIFICATION
Voltage: 120V~60 Hz
Absorbed power: 1250W
Pressure: 15 bar
Water tank capacity: 67.62 . oz. / 2.0 liters max.
Size Lxhxd: 9.3x13.8x17.5 in / 238x350x445 mm
Cable length: 2,92 ft / 1.80 m
Weight: 260 lb / 11.8 kg
Beans container capacity: 8.82 oz / 250 g max.
Please note
The lter lasts about two months if the appliance is used
normally. If the coee maker is left unused with the lter
installed, it will last a maximum of three weeks.
3. Remove the tank from the appliance and ll with water.
4. Insert the lter in the water tank and immerse it
completely for ten or so seconds, sloping it to enable the
air bubbles to escape (g. 34).
5. Insert the lter in the lter housing (g. 35A) and press as
far as it will go.
6. Close the tank with the lid (g. 35B), then replace the tank
in the machine.
When you install the lter, you must notify the appliance of its
presence.
7. Press the MENU/ESC button to enter the menu;
8. Press the MILK or
CAPPUCCINO button
(g. 8) until “Install
lter” is displayed;
9. Press the
button;
10. The message “Enable?” is
displayed.
11. Press the
button to conrm the
selection. “Hot water
Conrm?” is displayed.
12. Position a container with
a minimum capacity of
3.4 oz / 100 ml under the
hot water spout.
13. Press the
button to conrm the
selection. The appliance
begins delivering hot
water and the message
“Please wait “ is
displayed.
14. After delivery, the
appliance returns
automatically to the
“Ready for coee”
position.
The new lter is active. You can
now use the coee maker.
Replacing the lter
When “REPLACE FILTER” is
displayed, after two months
(see date indicator) or when
