15
Preparations
Preparing for surround sound
Speaker settings
If you selected other than “LRG” as the center speaker setting.
1 SURR YES: Surround speakers are connected to the re-
ceiver.
2 SURR NO: No surround speakers are connected to the
receiver.
9 Press the SET UP key to accept the setting.
Turn on the power to this receiver by pressing POWER and
ON/STANDBY key.
Select a speaker system.
1
2
3
1 Press the SET UP key to make the subwoofer setting indica-
tion (SUBW) appear.
2 Use the MULTI CONTROL to select the appropriate subwoofer
setting.
1 SUBW YES: A subwoofer is connected to the receiver.
2 SUBW NO: No subwoofer is connected to the receiver.
• When the setting "SUBW NO" is selected, the front speakers
automatically are set to "Large" and the procedure skips to step 5.
3 Press the SET UP key to accept the setting.
•The front speakers setting indication (FRNT) appears.
4 Use the MULTI CONTROL to select the appropriate front
speakers setting.
1 FRNT NML (normal): Average size front speakers are
connected to the receiver.
2 FRNT LRG (large): Large front speakers are con-
nected to the receiver.
5 Press the SET UP key to accept the setting.
•The center speaker setting indication (CNTR) appears.
Adjust the volume levels for the speakers.
The channel indication blinks while the test tone is being output.
Sit in your normal listening position and listen to the test tone. Adjust the
volume levels for the speakers until all speakers seem to be equally loud.
1 Use the MULTI CONTROL to adjust the volume when the test
tone is being output from the speaker channel to be adjusted.
The test tone issues from the speakers for 2 seconds at a time
in the following sequence:
Lch = Cch = Rch = RS = LS = SW = Lch
•If you change the volume level settings for the speakers while listening
to music, the settings referred to on this page are also changed.
¶
• If the speaker setting selects are changed, the speaker level settings
are reset.
2 Press the SET UP key.
•The receiver enters the mode for inputting the distance to the
speakers.
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
Continued to next page
If you selected “NML” as the front speakers setting.
1 CNTR YES: A center speaker is connected to the
receiver.
2 CNTR NO: No center speaker is connected to the
receiver.
7 Press the SET UP key to accept the setting.
•The surround speaker setting indication (SURR) appears.
8 Use the MULTI CONTROL to select the appropriate surround
speaker setting.
If you selected “LRG” as the center speaker setting.
1 SURR LRG (large): Large surround speakers are con-
nected to the receiver.
2 SURR NML (normal): Average size surround speakers are
connected to the receiver.
3 SURR NO: No surround speakers are connected
to the receiver.
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP A
STEREO
STEREO
R
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
L
SP A
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP A
STEREO
6 Use the MULTI CONTROL to select the appropriate center
speaker setting.
If you selected “LRG” as the front speakers setting.
1 CNTR LRG (large): A large center speaker is connected to
the receiver.
2 CNTR NML (normal): An average size center speaker is con-
nected to the receiver.
3 CNTR NO: No center speaker is connected to the
receiver.
•The receiver enters the speaker volume level adjustment mode.
• In steps 3 and 4, indications appear only for the selected channels
of the speakers that require adjusting.
MULTI
CONTROL
SET UP
MULTI CONTROL
KRF-V6030D/
V5030D/
V4530D
SET UP
RC-R0610
SET UP
RC-R0510
MULTI
CONTROL
POWER
ON/STANDBY
