30
Connecting the HT-R520
—Continued
With (Remote Interactive) you can control your
-compatible Onkyo CD player, DVD player, and so
on with the HT-R520’s remote controller, and use the
following special functions:
Auto Power On/Standby
When you start playback on a component connected via
, if the HT-R520 is in Standby, it will turn on and
select that component as the input source automatically.
Similarly, when the HT-R520 is set to Standby, all com-
ponents connected via also enter Standby. This func-
tion will not work if the component’s power cord is
connected to the HT-R520’s AC OUTLET.
Direct Change
When playback is started on a component connected via
, the HT-R520 automatically selects that component
as the input source. If your DVD player is connected to
the HT-R520’s multichannel input, you must press the
[MULTI CH] button to enjoy all channels (see page 33).
This is because the Direct Change function only
selects the FRONT DVD IN sockets.
Remote Control
You can use the HT-R520’s remote controller to control
other -compatible Onkyo components.
Notes:
• Push plugs in all the way to make good connections.
• Use only cables for connections. cables
are supplied with Onkyo players (DVD, CD, etc.).
• Some components have two sockets, you can con-
nect either one to the HT-R520. The other is for con-
necting additional -compatible components.
• Connect the HT-R520’s socket to only Onkyo
components. Connecting to other manufacturer’s
components may cause them to malfunction.
• Some components may not support all functions.
Refer to the manuals supplied with your components.
The HT-R520 has AC outlet on its rear panel for con-
necting the power cord of another AV component. The
other component’s power switch can be left in the ON
position so that it turns on or off when the HT-R520 is
set to On or Standby.
Caution:
• Make sure that the capacity of the component that you
connect to the AC OUTLET does not exceed the stated
capacity (e.g., 100 W).
Note:
• Onkyo components with sockets should be con-
nected to regular wall outlets.
Notes:
• Before connecting the power cord, connect all of
your speakers and AV components.
•Turning on the HT-R520 may cause a momentary
power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem,
plug the HT-R520 into a different branch circuit.
Connecting Onkyo Components
To use , you must make an analog audio
connection (RCA) between the HT-R520 and
the other component, even if they are con-
nected digitally.
L
R
ANTENNA
FM
75
AM
OPTICAL COAXIAL
123
DIGITAL
IN
REMOTE
CONTROL
IN
IN
IN
IN
IN IN
IN
IN
FRONT
SURR
CENTER
SUB
WOOFER
OUT
OUT
OUT
VIDEO 2
VIDEO 1
DVD MONITOR
OUT
VIDEO
S VIDEO
DVD
TAPE
CD
L
R
VIDEO 2
VIDEO 1
SUBWOOFER
PRE OUT
VIDEO 1
/2/3IN
DVD
IN
COMPONENT VIDEO
Y
P
B
PR
OUT
L
R
LR
FRONT
DVD
L
R
IN
CD
L
R
REMOTE
CONTROL
ANALOG
AUDIO OUT
LR
ANALOG
AUDIO OUT
e.g., CD player
e.g., DVD player
Connecting the Power Cords of Other
Components
Connecting the Power Cord
AV RECEIVER
MODEL NO. HT
-
R
520
AC OUTLET
AC 120
V 60
Hz
SWITCHED
120
W 1
A
MAX.
R
L
R
L
FRONT
SPEAKERS A
Class 2 Wiring
SURROUND
SPEAKERS
CENTER
SPEAKER
SURROUND BACK
SPEAKER
FRONT
SPEAKERS B
R
L
AC OUTLET
AC 120
V 60
Hz
SWITCHED
120
W 1
A
MAX.
