Specifications
33
(1) Power ON, current probe method:
18.3 A (100 V), 37.1 A (240V)
(2) Hot switching inrush current,
measured in accordance with
European standard EN55103-1:
35.5 A (230 V)
LMD-2450W:
(1) Power ON, current probe method:
21.8 A (100 V), 40.6 A (240V)
(2) Hot switching inrush current,
measured in accordance with
European standard EN55103-1:
38.8 A (230 V)
Dimensions LMD-2050W: Approx. 518.5 × 468.4
× 269.9 mm (including the
projection parts)
(20
1
/2 × 18
1
/2 ×10
3
/4 inches)
(w/h/d)
LMD-2450W: Approx. 602.4 × 497.9
× 269.9 mm (including the
projection parts)
(23
3
/4 × 19
5
/8 × 10
3
/4 inches)
(w/h/d)
Mass LMD-2050W: Approx. 10.1 kg (22 lb
4 oz) (when no input adaptor is
installed)
Approx. 10.5 kg (23 lb 2 oz) (when two
BKM-229X are installed)
LMD-2450W: Approx. 11.0 kg (24 lb
4 oz) (when no input adaptor is
installed)
Approx. 11.4 kg (25 lb 2 oz) (when two
BKM-229X are installed)
Operating conditions
Temperature0 °C to 35 °C (32 °F to 95 °F)
Recommended temperature
20 °C to 30 °C (68 °F to 86 °F)
Humidity 30 % to 85 % (no condensation)
Pressure 700 hPa to 1060 hPa
Storage and transport conditions
Temperature–20 °C to + 60 °C (–4 °F to 140 °F)
Humidity 0 % to 90 %
Pressure 700 hPa to 1060 hPa
Accessories supplied
AC power cord (1)
AC plug holder (1)
Operating Instructions (1)
CD-ROM (1)
Warranty Card (1)
Using the CD-ROM Manual (1)
Optional accessories
SDI 4:2:2 input adaptor
BKM-220D
HD/D1-SDI input adaptor
BKM-243HS
NTSC/PAL input adaptor
BKM-227W
Analog component input adaptor
BKM-229X
Mounting bracket
MB-529 (for LMD-2050W)
Design and specifications are subject to change without
notice.
Pin assignment
PARALLEL REMOTE connector
Modular connector
(8-pin)
You can allocate functions using the REMOTE menu
(see page 29).
Wiring required to use the Remote Control
Connect the function you want to use with a Remote
Control to the Ground (Pin 5).
SERIAL REMOTE (RS-232C) connector
D-sub 9 pin, female
Note
Always verify that the unit is operating properly before
use. SONY WILL NOT BE LIABLE FOR
DAMAGES OF ANY KIND INCLUDING, BUT
NOT LIMITED TO, COMPENSATION OR
REIMBURSEMENT ON ACCOUNT OF THE LOSS
OF PRESENT OR PROSPECTIVE PROFITS DUE
TO FAILURE OF THIS UNIT, EITHER DURING
THE WARRANTY PERIOD OR AFTER
EXPIRATION OF THE WARRANTY, OR FOR ANY
OTHER REASON WHATSOEVER.
Pin number Functions
1 Designating composite input signal
2 Designating component input signal
3 Setting tally lamp green ON/OFF
4 Setting tally lamp red ON/OFF
5 GND
6 Selecting external sync.
7 Selecting over scan
8 Selecting normal scan
Pin number Signal
1 NC
1
8
15
69
