3
TABLE NO. 1
Burner Gas type Pressur
e
Nozzle
diameter
Nominal flow rate
mbar 1/100 mm g/h l/h kw kcal/h
Natural Gas G20 20 72 - 95 1 860
Auxiliary Butane G30 30 50 73 - 1 860
Propane G31 37 50 71 - 1 860
Natural Gas G20 20 97 - 167 1,75 1505
Semirapid Butane G30 30 65 127 - 1,75 1505
Propane G31 37 65 125 - 1,75 1505
Natural Gas G20 20 115 - 286 3 2580
Rapid Butane G30 30 85 218 - 3 2580
Propane G31 37 85 214 - 3 2580
Natural Gas G20 20 120 - 276 2,9 2494
Fish burner Butane G30 30 85 211 - 2,9 2494
Propane G31 37 85 207 - 2,9 2494
Ultra Natural Gas G20 20 135 - 334 3,5 3010
Rapid Butane G30 30 95 254 - 3,5 3010
Propane G31 37 95 250 - 3,5 3010
(model with gas oven and gas grill with double controls)
Natural Gas G20 20 135 - 352 3,7 3182
Oven Butane G30 30 90 269 - 3,7 3182
Propane G31 37 90 264 - 3,7 3182
Natural Gas G20 20 115 - 191 2 1720
Grill Butane G30 30 68 145 - 2 1720
Propane G31 37 68 143 - 2 1720
(model with gas oven and gas grill with single control, or gas oven and electric grill)
Natural Gas G20 20 150 - 429 4,5 3870
Oven Butane G30 30 90 327 - 4,5 3870
Propane G31 37 90 321 - 4,5 3870
Natural Gas G20 20 115 - 191 2 1720
Grill Butane G30 30 68 145 - 2 1720
Propane G31 37 68 143 - 2 1720
ADJUSTING THE BURNERS
Adjusting the ”MINIMUM” of the burners:
Hob burner adjustment: follow the instructions below to adjust the minimum of the hob burners:
1. Light the burner setting the knob to the MINIMUM position (small flame).
2. Turn the knob of the tap, secured by simple pressure on the rod.
3. If the cooker does not have safety valves on the hob burners, insert a small slotted screwdriver in the hole of
the tap rod (Figure 12) and turn the choke screw to the right or left, until the burner flame is at the minimum; if
the cooker has safety valves, the choke screw is not situated on the rod hole, but on the body of the tap (Figure
13).
4. Make sure the flame does not go out, when switching quickly from the MAXIMUM to the MINIMUM position.
Oven burner adjustment: follow the instructions below to adjust the minimum of the burners:
1. Unplug the appliance before making the adjustment
2. Remove the knobs
3. Remove the control panel by removing the screws from the below the panel
4. Insert the thermostat knob
5. Light the burner setting the knob to the MAXIMUM position (manual lighting with a match)
6. Close the oven door and operate the oven for at least 10 minutes.
7. Set the knob to the MINIMUM position (120°) and then remove it.
8. Use a slotted screwdriver on the choke screw (Figure
9. 14) and, while observing the flame at the same time through the cooker porthole, evaluate the consistency of
the flame so it remains on when switching quickly from the MINIMUM to the MAXIMUM position.
10. Reassemble the front panel, proceeding as above in point 3, in reverse
Grill burner adjustment: follow the instructions below to adjust the minimum:
1) Light the burner setting the knob to the MAXIMUM position.
2) Close the oven door and operate the oven for at least 10 minutes.
3) Set the knob to the MINIMUM position (small flame) and then remove it.
4) The cooker is equipped with safety valves, use a small slotted screwdriver on the valve body (see fig. 13) and
turn the choke screw to the right or left, while observing the flame at the same time through the cooker porthole,
evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the MAXIMUM
position.
WARNING: The above-mentioned adjustment should be made only with natural gas burners, while for
those operating with liquid gas the screw must be locked at the end in a clockwise direction.
