ADJUST
Input gain settings
Input gain setting
(p. 68-D3)
DUCKER DEPTH –20
Ducker attenuation level setting (p. 72-D15)
(For the channel on which the D-001T is used)
(For the channel on which the AN-001T is not used)
BASS+12 TRE
B
LE–10
BASS and TREBLE settings (p. 69-D4)
L
O
UDNESS–
O
N
Loudness compensation setting (p. 69-D5)
EQ ON/OFF, Band number, Gain, Q,
and Center frequency settings (p. 69-D6)
HPF and LPF settings
(p. 69-D7)
C
O
M
PRESS
O
R–
OF
F
Compressor setting (p. 70-D8)
V
O
X SENSITIV
I
TY–30
VOX (Voice Operated Exchange) setting
(p. 70-D9)
E
Q
10 +12 07 315
..
EQ ON/OFF, Band number, Gain, Q,
and Center frequency settings
(p. 69-D6)
E
Q
10 +12 07 315
..
HPF–400 HZ L
P
F–125
.
Output channel selection
and
Output gain settings
Output channel selection and Output gain setting
(p. 72-D16)
BASS+12 TRE
B
LE–10
BASS and TREBLE settings (p. 69-D4)
L
O
UDNESS–
O
N
Loudness compensation setting (p. 69-D5)
C
O
M
PRESS
O
R–
OF
F
Compressor setting (p. 70-D8)
HPF and LPF settings (p. 69-D7)
HPF–400 HZ L
P
F–125
.
Speaker parameter presetting (p. 73-D17)
S
P
E
Q
ALL FL
A
T
IN1–IN1
ON
00
.
:
O
UT1–
O
UT1
ON
00
.
:
Setting menu screen
Note
Press the Enter key
to confirm this setting.
INPUT01
O
N
EVENT01–R
O
UTE
O
N
(Normal matrix operation)
Event selection (p. 68-D1)
(1-channel or 2-channel output operation)
Gain ratio setting (p. 71-D13)
(For the channel on which the AN-001T is used and the ANC operation is set to ACTIVE)
Lowest output level setting
(p. 70-D10)
SA
M
PLE T I
M
E 20
Sampling time setting (p. 71-D12)
G
AIN RATI
O
3:3
Reference level adjustment (p. 72-D14)
ANC ADJ 0 :SENS 8
M
INI
M
U
M
LEVEL –6
M
AX I
M
U
M
LEVEL 0
Highest output level setting
(p. 71-D11)
Input channel selection (p. 68-D2)
Note
The selectable output channel in the 1-channel
output operation method is OUTPUT 1 only.
UTILITYMEMORY
Normal use state
PARAMETER
Press for over 2 seconds.
To turn on,
ON/OFF
To turn on,
ON/OFF
To select,
PARAMETER
To select,
PARAMETER
To select,
INPUT VOLUME
To select,
OUTPUT SEL
To select,
OUTPUT VOLIME
13.8.2. Adjustment mode setting flow chart
The screen display examples shown at right may differ from
actual displays.
The on-screen indications shown in red here (actually shown by
flashing cursors) are parameters or setting contents to be
selected with the Parameter setting knob, input channel
selection key or other designated keys.
ÇsThe indications of the [ ], [ ], [ ], and [ ] arrows
represent that the screen is switched with the Screen shift key.
Unless otherwise specified, use the Parameter setting knob for
each parameter selection.
