D-5.5E ONLY
Stereo phone jack is wired : Tip=Left, Ring=Right and Sleave=Common.
All XLR type connectors are electronically balanced.
The XLR type connectors are wired as follows Pin No.l-Ground, Pin No.2-Cold (Low), Pin No.3-Hot (High)
OUTPUT SPECIFICATIONS (D-5.5, D-5.5E)
D-5.5E ONLY
All XLR type connectors are electronically balanced.
The XLR type connectors are wired as follows. Pin No.1-Ground, Pin No.2-Cold (Low), Pin No.3-Hot (High)
0dB is referenced to 0.775V RMS
Connector
¼" PHONE JACK
RCA PIN JACK
XLR-3-32 TYPE
¼" PHONE JACK
RCA PIN JACK
¼" PHONE JACK
RCA PIN JACK
RCA PIN JACK
¼" PHONE JACK
¼" STEREO
PHONE JACK
Output Level
Nominal
MAX. Before Clip
For Use With Nominal
Actual Source Impedance
Output
GROUP 1~4
STEREO L & R SUM
AUX1 SEND, AUX2 SEND
REV SEND, EFF SEND
ACCESSORY OUT
PRE/POST (INPUT, GROUP,
STEREO, SUM)
DIRECT OUT 1~8
<9~20>
CUE OUT L & R
PHONES
Input
MIC 1~8
<9~20>
INPUT 1~8
<9~20>
PAD
0
30
0
30
TAPE 1~8
<9~20>
PHONO (RIAA) 7 & 8
ACCESSORY IN PRE/POST
(INPUT, GROUP, STEREO,
SUM)
AUX1 RET, AUX2 RET
REV
RET,
EFF RET
CUE IN L & R
Actual Load
Impedance
For Use
With Nominal
INPUT SPECIFICATIONS (D-5.5, D-5.5E)
Input Level (Trim "0" to Trim "-30")
Nominal
-60dB (0.78mV)
to -30dB (25mV)
-30dB (25mV)
to 0dB (780mV)
-40dB (7.8mV)
to -10dB (250m V)
-10dB (250mV)
to + 20dB (7.8V)
-20dB (78mV)
to + 10dB (2.5V)
-50dB (2.5mV)
to -20dB (78mV) at 1kHz
-10dB (250mV)
-20dB (78mV)
-10dB (250mV)
MAX. Before Clip
-40dB (7.8mV)
to -10dB (250mV)
-10dB (250mV)
to +20dB (7.8V)
-20dB (78mV)
to +10dB (2.5V)
+10dB (2.5V)
to +40dB (78V)
0dB (780mV)
to +30dB (25V)
-30dB (25mV)
to 0dB (780mV) at 1kHz
+ 10dB (2.5V)
EXCEPT GROUP, STERO,
SUM. ACCESSORY IN POST
+6dB (1.6V)
+10dB (2.5V)
+24dB (12V)
Connector
XLR-3-31 TYPE
¼" PHONE JACK
RCA PIN JACK
RCA PIN JACK
RCA PIN JACK
¼" PHONE JACK
¼" PHONE JACK
0dB is referenced to 0.775V RMS
Accessory (D-5.5E ONLY)
BUSS LINK CABLE 6ft. 1
* 0dB is referenced to 0.775V RMS
Specifications are subject to change without notice.
Weight
D-5.5, D-5.5E
22kg (48.5lbs)
Dimensions (W×D×H)
Power Consumption
D-5.5 41W
D-5.5E 39W
Meter ("0" = Nominal level of STEREO, SUM OUT and CUE bus)
pair of 12 segment bargraph LED meter for STEREO L, R or SUM,
CUE
Phantom Power
48V DC is applied to MIC Input for powering condenser mic-
rophones
Sig./Peak Indicator
Equalization
LOW ±15dB 20Hz Shelving
MID ±15dB 200Hz to 5kHz Variable Peaking
HIGH ±15dB 20kHz Shelving
Sig. (Green) LED turn on at -30dB below nominal level
Peak (Red) LED turn over from Sig. (Green) at -3dB below clipping
Maximum Voltage Gain
MIC IN to SUM OUT
MIC IN to STEREO OUT
MIC IN to GROUP OUT
INPUT to GROUP OUT
INPUT to AUX½, REV, EFF SEND
AUX½, REV, EFF RET to GROUP OUT
All Fader minimum
Master (GROUP, STEREO or SUM) Fader
Nominal, D-5.5 only
Master (GROUP) Fader Nominal, D-5.5E con-
nection
Master (GROUP) and One Input Fader
Nominal
Equivalent Input Noise (MIC IN)
Equivalent Input Noise IHF-A weighted (MIC IN)
Hum and Noise (20Hz to 20kHz)
Total Harmonic Distortion
Less than
Less than
(MIC
IN)
(INPUT)
GENERAL SPECIFICATIONS
Frequency Response
+0dB, -0.5dB 50Hz to 20kHz
+0dB, -3.0dB 20Hz to 50kHz
Specifications (D-5.5, D-5.5E)
MICROPHONES
or LOWER
IMP. LINES
or LOWER
IMP. LINES
or LOWER
IMP. LINES
or LOWER
IMP. LINES
or LOWER
IMP. LINES
Lines
Lines
Lines
Lines
Lines
Lines
or higher
+4dB
(1.2V)
-10dB (250mV)
+4dB (1.2V)
+4dB (1.2V)
-10dB (250mV)
+4dB (1.2V)
+ 10dB (250mV)
-10dB (250mV)
+4dB (1.2V)
+20dB (7.8V)
+6dB (1.6V)
+20dB (7.8V)
+ 20dB (7.8V)
+ 6dB (1.6V)
+20dB (7.8V)
+ 20dB (7.8V)
+ 10dB (2.5V)
+ 20dB (7.8V)
-6dB (390mV)/8
+ 20dB (7.8V)/OPEN
104dB
94dB
84dB
64dB
54dB
34dB
-125dB*
-127dB*
-100dB*
-70dB*
-65dB*
-61dB*
0.3%
0.1%
+4dB*
+4dB*
1kHz
1kHz
— 17 —
