Advanced operations
32
B
A
LS
RS
L
R
SW
f
e
d
a
C
SETUP
SELECT
ENTER RETURN
ms
ms
dB
0
dBdB
L
Exit
Test
LS
R
SW
C
RS
dB
0
0
0
0
0
LS
LS
acaba
c
(L)
bc
(L)
aca
(R) (R)
1234
5678
90
S
10
CANCEL
OPEN/CLOSE
POWER
MARKER
TEXTPAG EGROUP
ENTER
VIDEO OFF
PLAY MODE SUBTITLE
AUDIO ANGLE
TOP MENU
MENU
ON SCREEN RETURN
PLAY LISTDIRECT NAVI
SET UP
Í
/I
AUDIO
/
VIDEO
ENTER
Changing settings
Speaker setting
[DVD-A] [DVD-V]
Change speaker size and presence =, delay time >, and channel
balance ? to suit the speakers you have connected.
These settings are not necessary when you select “2-channel”
(only two speakers are connected).
Speaker presence and size (=)
1. Press the cursor buttons [3, 4, 2, 1] to select the item and
press [ENTER].
2. Press the cursor buttons [3, 4] to select the setting and
press [ENTER].
Icon examples: Rear speaker (L)[A]
Large: When the speaker supports low-frequency (under 100 Hz)
reproduction.
Small: Select when the speaker does not support low-frequency
reproduction.
The size setting for the main speakers is automatically determined
by the setting for the subwoofer.
»
B
Delay time (>)
[DVD-V] (Dolby Digital, center and rear speakers only)
For optimum listening with 5.1-channel sound, all the speakers, ex-
cept for the subwoofer, should be the same distance from the seat-
ing position. If you have to place the center or rear speakers closer
to the seating position, adjust the delay time to make up for the dif-
ference.
If distance @ (from the center speaker) and B (from the rear speak-
ers) are the same as or greater than A (from the main speakers),
leave the delay time as “0”, the factory preset.
If either distance @ or B is less than A, find the difference in the
relevant table and change to the recommended setting.
Changing the delay time
1. Press the cursor buttons [3, 4, 2, 1] to select the delay
time box and press [ENTER].
2. Press the cursor buttons [3, 4] to adjust the delay time and
press [ENTER].
Speaker balance (?)
1. Press the cursor buttons [3, 4, 2, 1] to select “Test” and
press [ENTER].
A test signal is output from one speaker at a time, starting with
the main left speaker and proceeding clockwise.
MAIN (L)>CENTER>MAIN (R)
:;
REAR (L)(-----------==REAR (R)
2. While listening to the test signal, press the cursor buttons
[3, 4] to adjust the volume of the center and rear speakers
so they are the same apparent volume as the main speakers
(s6 dB to r6 dB).
(The main speakers cannot be adjusted here.)
3. Press [ENTER].
The test signal stops.
Note
³Test signal is effective only when you made analog connection.
When you make digital connection, make adjustment using the
test tone on the amplifier.
³No signal is output for the subwoofer. To adjust its volume, play
something, then return to this screen to adjust to suit your taste.
When you are finished
Press the cursor buttons [3, 4, 2, 1] to select “Exit” and press
[ENTER].
Note
The unit may be unable to output as set here due to limitations im-
posed by the unit itself or the disc being played. (The FL display’s
“P.PCM” indicator lights or “D.MIX” indicator goes out in these
cases.)
No Small
Difference
Approx. 200 cm (6 feet)
Approx. 400 cm (12 feet)
Approx. 600 cm (18 feet)
Setting
5.3 ms
10.6 ms
15.9 ms
Difference
Approx. 50 cm (1
1
/2 feet)
Approx. 100 cm (3 feet)
Approx. 150 cm (5 feet)
Approx. 200 cm (6 feet)
Setting
1.3 ms
2.6 ms
3.9 ms
5.3 ms
³Center speaker
³Rear speakers
Main (L)
Center
Main (R)
Test
signal
Exit
Rear
Subwoofer
Large
Cursor
buttons/ENTER
