Chapter 35 Access Control
GS2200-8/24 User’s Guide
273
intrusionlock IntrusionLockEventOn 1.3.6.1.4.1.890.1.5.8.55.27.2.1
1.3.6.1.4.1.890.1.5.8.56.27.2.1
1.3.6.1.4.1.890.1.5.8.59.27.2.1
1.3.6.1.4.1.890.1.5.8.60.27.2.1
This trap is sent when intrusion lock
occurs on a port.
loopguard LoopguardEventOn 1.3.6.1.4.1.890.1.5.8.55.27.2.1
1.3.6.1.4.1.890.1.5.8.56.27.2.1
1.3.6.1.4.1.890.1.5.8.59.27.2.1
1.3.6.1.4.1.890.1.5.8.60.27.2.1
This trap is sent when loopguard shuts
down a port.
errdisable errdisableDetect 1.3.6.1.4.1.890.1.5.8.55.130.4.
1
1.3.6.1.4.1.890.1.5.8.56.130.4.
1
1.3.6.1.4.1.890.1.5.8.59.130.4.
1
1.3.6.1.4.1.890.1.5.8.60.130.4.
1
This trap is sent when an error is detected
on a port, such as a loop occurs or the
rate limit for specific control packets is
exceeded.
errdisableRecovery 1.3.6.1.4.1.890.1.5.8.55.130.4.
2
1.3.6.1.4.1.890.1.5.8.56.130.4.
2
1.3.6.1.4.1.890.1.5.8.59.130.4.
2
1.3.6.1.4.1.890.1.5.8.60.130.4.
2
This trap is sent when the Switch ceases
the action taken on a port, such as
shutting down the port or discarding
packets on the port, after the specified
recovery interval.
fanspeed FanSpeedEventOn 1.3.6.1.4.1.890.1.5.8.56.27.2.1
1.3.6.1.4.1.890.1.5.8.60.27.2.1
This trap is sent when the fan speed goes
above or below the normal operating
range.
FanSpeedEventClear 1.3.6.1.4.1.890.1.5.8.56.27.2.2
1.3.6.1.4.1.890.1.5.8.60.27.2.2
This trap is sent when the fan speed
returns to the normal operating range.
poe PwrPortFailedEventOn 1.3.6.1.4.1.890.1.5.8.56.27.2.1
1.3.6.1.4.1.890.1.5.8.60.27.2.1
This trap is sent when the port is turned
off to supply power due to overloading,
over system buget, or short circuit.
PwrPortFailedEventClear 1.3.6.1.4.1.890.1.5.8.56.27.2.2
1.3.6.1.4.1.890.1.5.8.60.27.2.2
This trap is sent when the port returns to
the normal state and has the ability to
supply power.
PsePwrFailedEventOn 1.3.6.1.4.1.890.1.5.8.56.27.2.1
1.3.6.1.4.1.890.1.5.8.60.27.2.1
This trap is sent when the power supply
of PoE failed. The trigger situation
includes internal/external power supply
failure, external fan speed failure, and
external power has exceed normal
temperature.
PsePwrFailedEventClear 1.3.6.1.4.1.890.1.5.8.56.27.2.2
1.3.6.1.4.1.890.1.5.8.60.27.2.2
This trap is sent when the power supply
of PoE returns to the normal state.
Table 112 SNMP System Traps (continued)
OPTION OBJECT LABEL OBJECT ID DESCRIPTION
