T440 Users manual V021/B, © JED Microprocessors Pty Ltd Nov 17th 2008 Page 25
Sony (Code 08 hex, Even Parity, Code 09 hex No Parity)
Even parity: SONY VPL-CX61/CX63/CX80/CX85/CX86/CX100/CX120/CX125/CX150/CX155, VPL-ES4/EX4
SONY_FE40/FX40/FX50/FX51/FX52/PX11/PX15/PX35/PX40/PX41: Code 08 hex
No parity: VPL-ES3/EX3: Code 09 hex
A protocol manual is at:
http://www.kavena.se/fileadmin/uploads/downloads/Sony/Projektorer/VPL-FX40/ProtocolRS232FX40.pdf
This family has common codes, but allocate the “Inputs A/B/C/D” differently.
Channel codes are:
Computer1 := A9 + 00 + 01 + 00 + 00 + 02 + 03 + 9A; // Input A VGA analog-RGB
Computer2 := A9 + 00 + 01 + 00 + 00 + 03 + 03 + 9A; // Input B or Component
Computer3 := A9 + 00 + 01 + 00 + 00 + 04 + 05 + 9A; // Input C or HDMI
Computer4 := A9 + 00 + 01 + 00 + 00 + 05 + 05 + 9A; // Input D or DVI
Video1 := A9 + 00 + 01 + 00 + 00 + 00 + 01 + 9A; // Composite Video RCA
Video2 := A9 + 00 + 01 + 00 + 00 + 01 + 01 + 9A; // S-Video
Video3 := A9 + 00 + 01 + 00 + 00 + 02 + 03 + 9A; // Input A (could be component)
Video4 := A9 + 00 + 01 + 00 + 00 + 03 + 03 + 9A; // Input B could be component)
Video5 := A9 + 00 + 01 + 00 + 00 + 04 + 05 + 9A; // Input C or HDMI
Video6 := A9 + 00 + 01 + 00 + 00 + 05 + 05 + 9A; // Input D or DVI
Any one of these codes can be set into Constant:0/Constant:1 for computer codes and Constant:2/Constant:3 for video
codes. (The default is to have Computer1 (above) as the “Computer” channel and Video1 as the “Video” channel.
Setting OPT1 switch ON will swap Video1 and Video2 channels, making S-Video the video default.)
• OPT7 handshake mode and power on panel connection blink codes available;
• Pressing a “Computer” channel key when already selected will instead send a Auto Pixel Align whenever needed;
• Setting OPT2 switch ON will send an Auto Pixel Align message 30 seconds after selecting a computer channel;
• Picture and sound mute is available with two-yellow-button mute mode, but no Freeze is available.
RS232 connections to Sony projectors and LCD flat panel
These all use a D-sub 9-pin connector, male on cable.
VPL- CX85/86, FX50/51/52, PX11/15/35/40/41 38400 BAUD, Even parity, 1 stop.
VPL- ES3/EX3, 38400 BAUD, No parity, 1 stop.
Function/Direction T440 “projector”
Connection
Projector Connector
(Male on cable)
Ground Ground 9-pin D-sub pin 5
Data from T440 to projector Tx 9-pin D-sub pin 2 (RXD)
Reply data from projector to T440 Rx 9-pin D-sub pin 3 (TXD)
Plus 9 volt CTS/DTR to projector N/C N/C
3
D-sub 9 male
solder side
4 25 1
9 8 7 6
After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins
in any installation, as described in the troubleshooting part of this manual.
