Filter
Top Products
8
Answering machine
CAUTION: To reduce the risk of personal injury, fire, or damage use only the
EM6113 power adaptor listed in the user’s guide. This power adaptor is
intended to be correctly orientated in a vertical or floor mount position.
5. Allow the phone to charge for 16 hours prior to first use. If you don't properly charge
the phone, battery performance is compromised
The integrated digital answering machine offers a total recording time of up to 11 minutes
for outgoing and incoming messages. Self recorded memos are treated like messages.
You can operate the answering machine at the base station. An internal voice will give
you advice. You can switch the language from German to french. Using a telephone
with tone dialling (DTMF) you have also a PIN protected remote access.
You can select between two mode:
- Answer and record
- Answer only
A standard announcement is already saved for every operating type at the delivery stage.
Therefore the answering machine is immediately operational. At “Answer and record” and
reaching of the maximum recording capacity the device will automatically switch to the
operating type “Answer only”.
If the answering machine is turned off the announcement for the operating type “Answer
only” will be played after approx. 10 rings.
When playback messages the voice will give you information about day and time of the
relevant call (only when date and time were set correctly).
The display gives you information:
XX Digits steadily on: Number of old (already heard) messages Flashing digits:
Number of new messages.
FL TAM memory is full.
Turning the answering machine on/o
Press briefly .
Number of rings - setting /checking
The number of rings after which the answering machine will answer calls can be set from
2 - 9 and tS (toll saver). The standard setting is 5 rings. In toll saver mode, the machine
will answer after 5 rings if there are no new messages, and after 2 rings if there are new
messages. If there are no new messages and you call your machine to check your
messages remotely, you can hang up after the 2nd ring. You do not need to pay
connection fees and you know that you do not have any new messages.
Press briefly to check the setting.
Press and HOLD to enter setting mode. Use the and to set the number
of rings.
Press for confirmation.
15
Dialing from the phonebook /viewing entries
The handset is in idle state
Press the button. Select and entry. Press the button repeatedly, to show the
telephone number and the melody.
Press the button. The displayed telephone number is being dialed.
Editing an entry
The handset is in idle state
Press the button.
Press the button. Select EDIT ENTRY, using the or the button, and press
the button. Edit name if necessary and press the button. Edit number if
necessary and press the button. Change melody and press the button.
Press the button to delete the last character or press and HOLD the button to
delete the whole entry. You can enter a dialing pause (approximately 3 seconds) by
pressing the button.
Press the button again to store the edited entry.
Deleting entries
When the desired entry is displayed, press the button. Select DELETE ENTRY
or DELETE ALL if necessary and press the button. The entry or all entries will be
deleted.
TALK
MEMORY
MEMORY
MEMORY
MEMORY
OK
MENU
OK
MENU
OK
MENU
OK
MENU
OK
MENU
OK
MENU
OK
MENU
MUTE
MUTE
REDIAL
CID
◄
OK
MENU
OK
MENU
OK
MENU
OK
MENU
/
/
OK
MENU
OK
MENU
OK
MENU
MEMORY
MUTE
MUTE
Phonebook
REDIAL
You can store up to 50 entries in the phonebook.
Storing an entry
The handset in the idle state.
Press the button. The first entry is shown in the display. If the phonebook is empty,
EMPTY will be displayed.
Press the button. Select NEW ENTRY if necessary and press the button.
Enter the name and press the button. Enter special characters and spaces by
pressing the “1” button. Enter the telephone number. Press the button to delete the
last character or press and HOLD the button to delete the whole entry. You can enter
a dialling pause (approximately 3 seconds) by pressing the button.
Area code
Press the button. Select HANDSET using and press the button.
Select AREA CODE using and press the button. Enter the area code using
key pad and confirm with the button.