0
Getting Started Connections Settings Remote ControlMulti-zone Information Troubleshooting Specifications
NOTE
Recordings you make are for your personal enjoyment and should
not be used for other purposes without permission of the copyright
holder.
Input sources for which “Delete” is selected at “Source Delete”
(vpage 42)cannot be selected.
•
•
To cancel, press <ZONE2/3 / REC SELECT>, then turn <SOURCE
SELECT> until “ZONE2 SOURCE” is displayed.
Make a test recording before starting the actual recording.
Signals are only output to the analog REC OUT connectors when
the digital signals input to the digital input connectors (OPTICAL/
COAXIAL) are PCM (2-channel) signals.
Digital audio signals input to the DENON LINK or HDMI connectors
are not output to the REC OUT connectors, so connect using the
OPTICAL or COAXIAL connectors.
Sources selected with the REC OUT mode are output from ZONE2
as well.
In the REC OUT mode, the remote control unit’s ZONE2 mode
buttons cannot be operated.
The “XM” and “HD Radio” digital audio output signals are not
output from the OPTICAL2 output connectors. Also, network audio
signals (Internet radio, music server, USB) are not output if they are
copyright-protected.
•
•
•
•
•
•
•
You can listen to one program source while recording a different
program source.
1
Press <ZONE2/3 / REC SELECT> .
“ZONE2 SOURCE” is shown on the display.
2
Turn <SOURCE SELECT> until “RECOUT SOURCE”
is displayed.
The “ ” indicator lights.
ZONE2 SOURCE ZONE2 PHONO ZONE2 HD Radio
····
RECOUT HD Radio RECOUT SIRIUS RECOUT SOURCE
····
3
Turn <SOURCE SELECT> to choose the input source
to be recorded.
4
Play the program source.
For operating instructions, refer to the respective equipment’s
operating instructions.
b
5
Start recording.
For operating instructions, refer to the respective equipment’s
operating instructions.
b
Recording on an External Device
(REC OUT mode)
Other Operations
When you make an HDMI connection with a TV or player compatible
with AVR-4310CI and HDMI control functions, you can perform the
following operations by setting the HDMI control function of each
device.
When you want to listen to TV audio by AVR-4310CI, connect optical
digital or analog audio (vpage 18 “Connecting the TV“).
When using these functions set as follows: “HDMI Control” –
“Control” (vpage 37) set to “ON“.
•
•
NOTE
When “Control” is set to “ON”, it consumes more standby power.
The HDMI control function controls operations of a TV that is
compatible with the HDMI control function. Make sure that the TV
and HDMI are connected when you perform HDMI control.
When you power off AVR-4310CI, the HDMI control function does
not operate. Either power on or set to standby.
Some functions may not operate depending on the connected TV
or player. Check the owner’s manual of each device for details
beforehand.
When “Control” is set to “ON”, it is not possible to assign an HDMI
terminal to “TV” at “Input Assign” (vpage 47).
•
•
•
•
•
1
Turn the power on for all the equipment connected
by HDMI cable.
2
Set the HDMI control function for all equipment
connected by HDMI cable.
Set “HDMI Control” – “Control” (vpage 37) to “ON“.
Please consult the operating instructions for the connected
equipment to check the settings.
Carryout steps 1 and 2 should any of the equipment be plugged
out.
b
b
3
Switch the television input to the HDMI connected to
the AVR-4310CI.
4
Switch the AVR-4310CI input to the HDMI input
source and check if the picture from the player is ok.
5
When you turn the TV’s power to standby, check
that the power of the AVR-4310CI and player also
goes on standby.
If the HDMI control function does not operate properly, check the
following points.
Is the TV or player compatible with the HDMI control function?
Is the AVR-4310CI properly set?
Is the “HDMI Control” – “Control” (vpage 37) set to “ON”?
Is the “Power Off Control” (vpage 37) set to “ON”?
Is the “Control Monitor” (vpage 37) set for the monitor output
connected to television?
Are the HDMI control function settings of all equipment correct?
•
•
•
•
•
•
NOTE
Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat step’s 1 and 2.
“Input Assign” – “HDMI” (vpage 47) setting has changed.
“Monitor Out” (vpage 37) setting is changed.
There is a change to the connection between the equipment and the
HDMI, or an increase in equipment.
•
•
•
AVR-4310CI power off can be linked to the TV power
off step.
When you set “Output audio from amp” in the TV audio output
setup operation, you can switch the amp power on.
You can switch audio output devices with a TV
operation.
You can adjust AVR-4310CI volume in the TV volume
adjustment operation.
You can switch AVR-4310CI input source through
linkage to TV input switching.
When playing the player, the AVR-4310CI input
function switches to the function of that player.
n
n
n
n
n
HDMI Control Function
Convenient Functions
Playback
