ENGLISH
Remote
Control
Playback
(Advanced)
Connections
Simple
Version
Playback
(Basic)
Multi-
zone
GUISettings
Getting
Started
Troubleshooting
Other
Information
Spec. Index
Part
Names
Setting items Setting details
Speaker Configuration
(Continued)
Surround Back : Set the presence, size and number of surround back
speakers.
Large : Use a large speaker that can adequately play back low
frequencies.
Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
None : Select when the surround back speakers are not connected.
2spkrs : Use two surround back speakers.
1spkr : Use only one surround back speaker. When you select this
setting, connect the surround back speaker to the left (L) channel.
Even when the “Surround Back“ setting is other than “None”, sound
may not be emitted from the surround back speaker, depending
on the playback source. In this case, make “Surround Parameters”
– “Surround Back” setting other than “OFF” (vpage 50).
NOTE
When the “Speaker Assign” setting (vpage 53) is other than “5.1CH +
Surround Back”, you cannot make the “Surround Back” setting.
•
•
•
•
•
Front Height : Set the presence and size of the front height speakers.
Large : Use a large speaker that can adequately play back low
frequencies.
Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
None : Select when the front height speakers are not connected.
NOTE
When the “Speaker Assign” setting (vpage 53) is other than “5.1CH +
Front Height”, you cannot make the “Front Height” setting.
•
•
•
Bass Setting
Set subwoofer and LFE
signal range playback.
Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
LFE : The low range signal of the channel set to “Small” speaker size is
added to the LFE signal output from the subwoofer.
LFE+Main : The low range signal of all channels is added to the LFE
signal output from the subwoofer.
This item can be set when “Speaker Configuration” – “Subwoofer”
(vpage 53) is set to “Yes”.
Play music or a movie source and select the mode offering the strongest
bass.
Select “LFE+Main” if you want the bass signals to always be produced
from the subwoofer.
•
•
•
•
•
Manual Setup
Setting items Setting details
Bass Setting
(Continued)
LPF for LFE : Set LFE signal playback range.
80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz
“LPF for LFE” can be set when “Speaker Configuration” – “Subwoofer”
(vpage 53) is set to “Yes”.
•
Distance
Set distance from listening
position to speakers.
Measure beforehand the
distance from the listening
position to each speaker.
Feet / Meters : Set the unit of distance.
Step : Set the minimum variable width of the distance.
1ft / 0.1ft
0.1m / 0.01m
•
•
Default : Reset all distance settings to factory default.
Yes
No
When you select “Default” and press ENTER, the “Return all settings
to the default?” prompt is displayed. Select either “Yes” or “No”, and
press ENTER.
•
•
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
Surround Back Lz / Surround Back Rz / Front Height L / Front Height
R : Select the speaker.
When the “Speaker Configuration” – “Surround Back” setting
(vpage 54) is set to “1spkr”, “Surround Back” is displayed.
0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance.
The speakers that can be selected differ depending on the “Speaker
Assign” (vpage 53) and “Speaker Configuration” (vpage 53, 54)
settings.
Default settings :
Front/Center/Subwoofer/Front Height : 12.0 ft (3.60 m)
Surround/Surround Back : 10.0 ft (3.00 m)
Set the difference in the distance between the speakers to less than 20
feet (6.0 meters).
NOTE
Speakers set to “None” in “Speaker Configuration” (vpage 53, 54) are
not displayed.
z
•
•
•
•
Remote control operation
buttons
Display the menu
Cancel the menu
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
