ENGLISH
Remote
Control
Playback
(Advanced)
Connections
Simple
Version
Playback
(Basic)
Multi-
zone
GUISettings
Getting
Started
Troubleshooting
Other
Information
Spec. Index
Part
Names
Setting items Setting details
Channel Level
Set the volume of the test
tone to be the same when it
is output from each speaker.
Test Tone : Output test tone.
Front L / Front Height L / Center / Front Height R / Front R / Surround R /
Surround Back Rz / Surround Back Lz / Surround L / Subwoofer :
Select the speaker.
When the “Speaker Configuration” – “Surround Back” setting
(vpage 54) is set to “1spkr”, “Surround Back” is displayed.
–12dB – +12dB (0dB) : Adjust the volume.
When o is pressed while the subwoofer volume is set to “–12 dB”,
the “Subwoofer” setting switches to “OFF”.
NOTE
Speakers set to “None” in the “Speaker Configuration” (vpage 53,
54) settings are not displayed.
When using surround speakers, be sure to adjust the volume of the
different speakers.
When a headphones jack is inserted in the PHONES terminal of this unit,
the “Channel Level” is not displayed.
•
z
•
•
•
•
Default : Reset all channel level settings to factory default.
Yes
No
•
•
Crossover Frequency
Set the maximum frequency
of the bass signal output
from each channel to
the subwoofer. Set the
Crossover Frequency to
suit the bass reproduction
capability of the speaker
being used.
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
Advanced : Specify crossover frequency for each speaker.
Front / Center / Surround / Surround Back / Front Height : Select the
speaker.
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
Crossover frequency can be set when the “Speaker Configuration”
– “Subwoofer” (vpage 53) setting is “Yes”, or when you have a
speaker that is set to “Small”.
Always set the crossover frequency to “80Hz”. When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
The speakers that can be set when “Advanced” is selected differ
according to the “Subwoofer Mode” setting (vpage 54).
When “LFE” is selected, speakers set to “Small” at “Speaker
Configuration” can be set. If the speakers are set to “Large”, “Full
Band” is displayed and the setting cannot be made.
If set to “LFE+Main”, this setting can be made regardless of the
speaker size.
•
•
•
•
•
•
•
Manual Setup
HDMI Setup
Default settings are underlined.
Make settings for HDMI video/audio output.
Setting items Setting details
HDMI Audio Out
Select HDMI audio output
device.
This can be set when the
input source on the unit
is “BD/SD”, “HDMI1”,
“HDMI2” or “HDMI3”.
Amp : Plays back using the speakers.
TV : Plays back on the TV.
When the HDMI control function is activated, priority is given to the TV
audio setting (vpage 39 “HDMI Control Function”).
HDMI Control
You can link operations with
devices connected to HDMI
and compatible with HDMI
Control.
Please consult the
operating instructions for
each connected component
to check the settings.
Refer to “HDMI Control
Function” (vpage 39) for
more information about the
HDMI control function.
NOTE
The HDMI control function
controls operations of a
TV that is compatible with
the HDMI control function.
Make sure that the TV and
HDMI are connected when
you perform HDMI control.
If the “Control” settings
have been changed,
always reset the power to
connected devices after
the change.
•
•
•
•
Control
ON : Use HDMI control function.
OFF : Do not use HDMI control function.
When a device that is not compatible with the HDMI control function
is connected, set “Control” to “OFF”.
NOTE
When “Control” is set to “ON”, it consumes more standby power.
If you are not using this unit for an extended period, it is recommended
that you unplug the power cord from the power outlet.
“HDMI Control” does not work when the power to the equipment is off.
Either turn power on or set to standby.
•
•
•
•
Standby Source : Sets the HDMI input source to put into standby when
the power is on.
Last : This item is set at the last-used input source.
HDMI1 / HDMI2 / HDMI3 : Put the respective input source into
standby.
“Standby Source” can be set when “Control” is set to “ON”.
•
•
Power Off Control : Links the power standby of this unit to external
equipment.
ON
OFF
“Power Off Control” can be set when “Control” is set to “ON”.
•
•
Remote control operation
buttons
Display the menu
Cancel the menu
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
