ENGLISH
Simple
Version
Remote
Control
Playback
(Advanced)
Connections
Playback
(Basic)
Multi-
zone
GUISettings
Getting
Started
Troubleshooting
Other
Information
Spec. Index
Part
Names
Set Up Speakers (Audyssey™ Auto Setup)
STEP 1
Preparation
STEP 2
Speaker Detection
STEP 3
Measurement
2
Set Up
the Subwoofer
If using a subwoofer capable of the
following adjustments, set up the
subwoofer as shown below.
When using a subwoofer with a direct
mode
Set the direct mode to “On” and disable the
volume adjustment and crossover frequency
setting.
When using a subwoofer without a
direct mode
Make the following settings:
Volume : “12 o’clock position”
Crossover frequency :
“Maximum/Highest Frequency”
Low pass filter : “Off”
Standby mode : “Off”
n
n
•
•
•
•
3
Connect the setup microphone to the
SETUP MIC jack of this unit.
FIRST SETUP 2/2
1 2 3 4 5 6
Speaker Assign
RETURN
Auto Setup Start
STEP1 Preparation
In a typical setup, select "Auto Setup Start". When connecting
speakers in a setup other than 2ch/2.1ch/5.1ch, select
"Speaker Assign".
Start Auto Setup
Enter Cancel
When the setup microphone is connected,
the following screen is displayed.
FIRST SETUP 2/2
RETURN
STEP1 Preparation
Please connect the include calibrated setup microphone
It prepares for beginning an auto setup.
Enter Cancel
When setting up speakers other than 5.1-channel
speakers, select “Speaker Assign”. When
the “Speaker Assign” setup screen appears,
perform the operations in Step 2 and 3 of “Set Up
Speakers” (vpage 36).
4
Select “Auto Setup Start” and then
press ENTER.
5
Select “Measure” and then press
ENTER.
When measuring begins, a test tone is output
from each speaker.
When measuring ends, the speaker detection
results are displayed.
FIRST SETUP 2/2
1 2 3 4 5 6
RETURN
Measure
STEP2 Speaker Detection
Please place the microphone at ear
height at main listening position.
Start measurement. Output large test tone during measuring
Enter Cancel
6
Select “Next → Measurement” and
then press ENTER.
7
Move the setup microphone to
position 2, select “Measure”, and
then press ENTER.
The measurement of the second position
starts. Measurements can be made in up to
six positions.
FIRST SETUP 2/2
1 2 3 4 5 6
RETURN
Next Calculation
Measure
STEP3 Measurement
Please place the microphone at ear
height at 2nd listening position (up to 6 position).
Start measurment. Output large test tone during measuring
Enter Cancel
8
Repeat step 7, measuring positions 3
to 6.
When measurement of position 6 is
completed, a “Measurements finished.”
message is displayed.
FIRST SETUP 2/2
1 2 3 4 5 6
Measure
RETURN
Next Calculation
Retry
STEP3 Measurement
Please place the microphone at ear
height at 3rd listening position (up to 6 position).
Start measurment. Output large test tone during measuring
Enter Cancel
If you want to omit measurements from the next
point onward, select “Next Calculation”.
(Go to vpage 8
STEP4 Calculation
)
If “Cancel” is Selected
“Cancel setup?” is displayed on the GUI screen.
If “Yes” is selected, “FIRST SETUP” closes.
Setting up the speakers again
Repeat the operation from step 3 of
STEP1 Preparation
.
The title of the GUI screen will change from
“FIRST SETUP” to “AUDYSSEY AUTO SETUP”
at this point, but the operation method is the
same.
n
•
NOTE
If “Caution!” is displayed:
Go to “Error Messages” (vpage 9), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
“Audyssey Auto Setup”.
When Performing Audyssey
Auto Setup Over Again
Press ui to select “Retry”, and then press
ENTER.
When Measuring has Stopped
Press RETURN, and the “Cancel setup?”
prompt is displayed.
Press o p and select “Yes”, then press
ENTER.
n
n
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
