Filter
Top Products
Radio Frequency (RF) Energy
This model phone meets the government’s requirements
for exposure to radio waves.
This phone is designed and manufactured not to exceed
the emission limits for exposure to radio frequency (RF)
energy set by the Federal Communications Commission
of the United States, Industry Canada of Canada.
During SAR testing, this device is set to transmit at its
highest certified power level in all tested frequency
bands , and placed in positions that simulate RF
exposure in usage against the head with no separation,
and near the body with the separation of 15 mm.
Although the SAR is determined at the highest certified
power level, the actual SAR level of the device while
operating can be well below the maximum value. This
is because the phone is designed to operate at multiple
power levels so as to use only the power required to
reach the network. In general, the closer you are to a
wireless base station antenna, the lower the power
output.
The exposure standard for wireless devices employs a
unit of measurement known as the Specific Absorption
Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg,
and 1.6W/kg by Industry Canada.
This device is compliance with SAR for general
population /uncontrolled exposure limits in ANSI/IEEE
C95.1-1992 and Canada RSS 102, and had been tested
in accordance with the measurement methods and
procedures specified in OET Bulletin 65 Supplement C,
and Canada RSS 102. This device has been tested, and
meets the FCC, IC RF exposure guidelines when tested
with the device directly contacted to the body.
The FCC has granted an Equipment Authorization for
this model phone with all reported SAR levels evaluated
as in compliance with the FCC RF exposure guidelines.
SAR information on this model phone is on file with the
FCC and can be found under the Display Grant section
of www.fcc.gov/oet/ea/fccid after searching on FCC ID:
Q78-Z660G.
For this device, the highest reported SAR value for
usage against the head is 1.23 W/kg, for usage near
the body is 1.19 W/kg.
While there may be differences between the SAR levels
of various phones and at various positions, they all
meet the government requirement.
SAR compliance for body-worn operation is based
on a separation distance of 15 mm between the unit
and the human body. Carry this device at least 15
mm away from your body to ensure RF exposure level
compliant or lower to the reported level. To support
body-worn operation, choose the belt clips or holsters,
which do not contain metallic components, to maintain
a separation of 15 mm between this device and the
your body.
RF exposure compliance with any body-worn accessory,
which contains metal, was not tested and certified, and
use such body-worn accessory should be avoided.
FCC Compliance
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly
approved by the manufacturer could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
CTIA
a) Do not disassemble or open crush, bend or deform,
puncture or shred.
b) Do not modify or remanufacture, attempt to insert
foreign objects into the battery, immerse or expose
to water or other liquids, expose to fire, explosion or
other hazard.
c) Only use the battery for the system for which it is
specified
d) Only use the battery with a charging system that has
been qualified with the system per CTIA Certification
Requirements for Battery System Compliance to IEEE
1725. Use of an unqualified battery or charger may
present a risk of fire, explosion, leakage, or other
hazard.
e) Do not short circuit a battery or allow metallic
conductive objects to contact battery terminals.
f) Replace the battery only with another battery that
has been qualified with the system per this standard,
IEEE-Std-1725. Use of an unqualified battery may
present a risk of fire, explosion, leakage or other
hazard.
Only authorized service providers shall replace
battery. (If the battery is non-user replaceable).
g) Promptly dispose of used batteries in accordance
with local regulations
h) Battery usage by children should be supervised.
i) Avoid dropping the phone or battery. If the phone or
battery is dropped, especially on a hard surface, and
the user suspects damage, take it to a service center
for inspection.
j) Improper battery use may result in a fire, explosion
or other hazard.
For those host devices that utilize a USB port as a
charging source, the host device’s user manual shall
include a statement that the phone shall only be
connected to CTIA certified adapters, products that
For Your SafetyFor Your Safety
82 83