Filter
Top Products
EAP page
You can configure various EAP (extensible authentication protocol) modules that are used for authentication and data
encryption. Note that corresponding values must be entered in the wireless LAN access point. EAP authentication is only available
if you have selected WPA/WPA2 or 802.1x as the security mode.
For instructions on editing the EAP module settings, see the Help function in the device.
WEP page
You can create up to four WEP keys. Corresponding values must be entered in the wireless LAN access point.
• WEP authentication — Select Open or Shared as a means of authentication between the wireless device and the wireless LAN
access point.
• WEP key in use — Select the WEP key you want to use with the Internet access point you are creating.
• Key #1 length — Select the appropriate key length. The more bits there are in the key, the higher the level of security. WEP
keys consist of a secret key and a 24-bit initialization vector. For example, some manufacturers refer to the 104-bit key as a
128-bit key (104+24). Both keys offer the same level of encryption and are therefore interoperable.
• Key #1 type — Select whether you want to enter the WEP key data in hexadecimal format (HEX) or in text form (ASCII).
• Key #1 data — Enter the WEP key data. The number of characters you can enter depends on the key length you have chosen.
For example, keys that are 40 bits long always consist of 5 alphanumeric characters or 10 hexadecimal characters.
EAP modules
EAP modules are used in a wireless LAN to authenticate wireless devices and authentication servers.
Note that the network must support this feature.
Modifying the EAP-SIM settings
To use EAP-SIM authentication, the cover phone must be switched on, and the device must have a valid SIM card installed.
To modify EAP-SIM settings for the Internet access point, select Connections > Internet setup. Select a wireless LAN Internet
access point from the list, and Edit > Advanced. Select the EAP page. Select EAP-SIM from the list, and press Configure.
Define the following:
• Use manual user name — This setting overrides the user name in the initial identity response in a case when the server
requires that the user performs the initial identification with a predefined user name, for example, with a Windows user
name. If you select Yes but leave the User name field empty, a random user name is generated for initial identity response.
• Use manual realm — This setting overrides the realm of the initial identity response in a case when the server requires that
the user performs the initial identification with a predefined realm. If you select No, the realm is derived from the IMSI
(international mobile subscriber identity).
• Use identity privacy — The EAP-SIM can have the server send a pseudonym identity for future authentications. This identity
prevents the user's IMSI from being sent.
• Max. reauthentic. count — The EAP-SIM can have the server send the wireless device a reauthentication identity that can be
used to speed up the upcoming authentications. You can specify how many times a single reauthentication mechanism can
be used until full authentication must be performed. If the reauthentications mechanisms are used too many times, security
may be compromised because the SIM card is not used in reauthentication.
Modifying the EAP-TLS settings
To modify the EAP-TLS settings for an Internet access point, select Connections > Internet setup. Select a wireless LAN Internet
access point from the list, and press Edit > Advanced. Select the EAP page. Select EAP-TLS from the list, and press Configure.
• On the User certificates page, select which personal certificates are used for user authentication when using this Internet
access point. This page shows all the installed personal certificates on the device. The certificates are enabled by default. To
disable a certificate, select the certificate, and press Disable.
• On the CA certificates page, select which authority certificates are valid for server verification in wireless LAN authentication
when using this Internet access point. This page shows all the installed authority certificates on the device. All certificates
are enabled by default. To disable a certificate, select the certificate, and press Disable.
• On the Cipher suites page, select which TLS (transport layer security) cipher suites you want to use with this Internet access
point. To enable a selected cipher suite, press Enable.
• On the Settings page, you can define additional settings related to EAP-TLS. For instructions on modifying these settings, see
the Help function in the device.
Modifying the EAP-PEAP settings
To modify the EAP-PEAP settings for an Internet access point, select Connections > Internet setup. Select a wireless LAN Internet
access point from the list, and press Edit > Advanced. Select the EAP page. Select EAP-PEAP from the list, and press Configure.
• On the User certificates page, select the personal certificates for user authentication when using this Internet access point.
This page lists all personal certificates installed on the device. The certificates are enabled by default. To disable a certificate,
select the certificate, and press Disable.
C o n t r o l p a n e l
Copyright © 2005 Nokia. All Rights Reserved. 70