Toshiba STRATA DK8 Cell Phone User Manual


 
SECTION 100-816-302
MARCH1993
transferring the call hangs up. When it does
hang up, the CO line call will then camp-on to
the busy station. The busy station will be
alerted of the camp-on by a camp-on tone (five
quick tone bursts), the CO line LED will flash
at the exclusive hold rate, and a message
(“CAMP-ON X”, X = the CO line number) will
appear on the LCD (if equipped). Among other
applications, one in which a VM/auto atten-
dant device that transfers calls to a typically
busy answering position station will benefit
from this feature-some auto attendant devices
cannot transfer a call to a busy station if BST
and BSR are not activated.
NOTE:
A BST station will receive ringback tone, in-
stead of busy tone, when transferring a call to a
busy BSR station.
l
Automatic Hold, LED 18-If this feature is
allowed, digital and electronic telephone users
with CO line buttons can place a CO line or
intercom call on hold and call another CO line
or station just by pressing another CO line
button or the
Intercom
button and dialing the
number-there is no need to press the
Hold
button to place the existing call on hold. If
Automatic Hold is denied with this LED, users
can put calls on hold and place calls, but they
will have to press the
Hold
button before
accessing another CO or intercom line.
NOTES:
7.
2.
0
0
CO lines or intercom calls that appear on
the intercom button will automatically hold
when accessing another CO line button.
IfAutomatic Holdis used, it is recommended
to program a
Release Call
button on
telephones via Program 39.
LCD Individual Message, LED 05-Turn
LED 05 ON to allow stations to store up to
ten personal LCD messages. Stations se-
lected with this feature will also be able to
assign alphanumeric memos to each of their
personal Speed Dial numbers.
Message Waiting (RCV), LED 04-If the
message waiting indication is not desired on
a digital or electronic telephone, this pro-
gram can be used to deny it. This does not
affect that station’s ability to send a mes-
sage waiting indication to another station.
LCD Type/32/12, LED 02-Digital tele-
phones and 6500-series LCD Electronic
Telephones have a 32-character display.
Therefore, assignments should be left in the
initialized state of 32 characters. LED 02
must be ON to receive avoice mail message
waiting indication.
LCD Display, LED 01-This option should
be used (LED 01 ON) for all stations (even
non-LCD) unless it is desired to disable the
station’s LCD and message waiting LED
function.
Disable Continuous DTMF tones, LED 17- Program 36-Fixed Call Forward: Fixed Call
Turns off continuous DTMF tones on 2000-
Forwarding is different from other station Call
series Digital telephones-may be required
Forwarding options. It is fixed in terms of the
for PC dialing telephone numbers using PDIU-
destination station number which is assigned in
D12 connected to a DKT 2000 telephone.
this program. The station user cannot change
No Call Forward/No Answer on Handsfree
this destination as is possible with other station
Answerback Call, LED 16-A Handsfree Call Forwarding options. This feature is valu-
Answerback call to an idle station in the Call
able for forwarding to voice mail devices or to an
Forward-No Answer mode or in the Call For-
attendant. If Fixed Call Forwarding is set on a
ward-Busy/No Answer mode will not forward if
station, the station will not ring and all calls will
this feature is activated. This prevents the call
forward.
from being forwarded 12 seconds after the
called party has been talking. Outside calls
and busy intercom calls to the station will
forward even if this feature is set. This feature
does not apply to off-hookcall announce calls;
the called station must answer an OCA call
within 12 seconds or the call will be forwarded
if CFNA is set.
NOTE:
The caller can press the “RING” Soft Key on a
digital telephone ordial 1 on a digitalorelectronic
telephone to activate Call Forward on Handsfree
Answerback calls.
2-16