No. 99MBC095A
viii
4.2.2 Entering the calibration mode......................................................... 4-25
4.2.3 Combined calibration ...................................................................... 4-27
4.3 Positioning a Gage or a Workpiece ............................................................ 4-29
4.4 How to read-in the amount of light ............................................................. 4-29
4.5 Setting Up the Functions ............................................................................ 4-31
4.5.1 Outline of the function setup mode ................................................ 4-31
4.5.2 Outline of each function setup mode ............................................. 4-32
4.5.3 Function setup mode ...................................................................... 4-33
4.5.3.1 F0: Setting the segment ....................................................... 4-34
4.5.3.2 F1:
Setting the measurement interval (measurement time) ...
4-36
4.5.3.3 F2: Setting the GO/NG judgment criteria ............................. 4-38
4.5.3.4 F3: Setting the reference value ............................................ 4-42
4.5.3.5 Analog voltage output and scale value ................................ 4-43
4.5.3.6 F4: Setting the preset/zero-set values ................................. 4-45
4.5.3.7 F5: Setting the data output conditions ................................. 4-47
4.5.3.8 F6: Setting the sample measurement .................................. 4-48
4.5.3.9 F7: Automatic workpiece detection setting .......................... 4-50
4.5.3.10 F8: Setting the group judgment............................................ 4-51
4.5.3.11 Confirming the function setup contents................................ 4-52
5. MEASUREMENT MODE ...................................................................................... 5-1
5.1 Outline of the Measurement Mode ............................................................... 5-1
5.1.1 Settings made in the measurement mode ....................................... 5-1
5.1.1.1 Setup operation from the arrow key....................................... 5-2
5.1.1.2 Setup that can be made directly from each setup item key .. 5-4
5.2 Other Functions ............................................................................................ 5-6
5.2.1 Key lock ............................................................................................ 5-6
5.2.2 Displaying the measuring position.................................................... 5-6
5.3 Applied Measurement ................................................................................... 5-7
5.3.1 OD measurement of a precision-machined workpiece .................... 5-7
5.3.2 Measurement of magnet coil wire that runs at high speed.............. 5-8
5.3.3 Measurement of the lead pitch of a multiple-pin IC ....................... 5-10
5.3.4 Applied Measurement with Preset/Zero-Set Functions .................. 5-12
5.3.5 Sample measurement..................................................................... 5-16
5.3.6
Application of the odd-numbered-edge cutting tool measurement ...
5-18
5.3.6.1 Odd-numbered-edge cutting tool outside diameter
measurement ........................................................................ 5-18
5.3.6.2 Odd-numbered-edge cutting tool run-out measurement ...... 5-20
5.3.7 Applied measurement with automatic workpiece detection ........... 5-22
5.3.8 Applied measurement on a stepped round bar.............................. 5-24
6. INTERFACE UNIT ................................................................................................ 6-1
6.1 Standard Interface ........................................................................................ 6-1
6.1.1 I/O Analog Interface.......................................................................... 6-1
6.1.1.1 External view of the connector ............................................... 6-1
6.1.1.2 Terminal names ...................................................................... 6-2
6.1.1.3 Input/output equivalent circuit................................................. 6-2
6.1.1.4 Timing chart ............................................................................ 6-5
6.1.2 RS-232C Interface ............................................................................ 6-7
6.1.2.1 Specifications.......................................................................... 6-7
6.1.2.2 Connections ............................................................................ 6-8
6.1.2.3 Printer interface .................................................................... 6-10
