Filter
Top Products
Index
Index-7
OTP memory cards, 8-21
open loop AGC calibration
RF analyzer, 4-113
Open/Auto DAC Value
RF Analyzer, 4-114
open-loop AGC
RF analyzer, 4-112
operating environment, 1-8
Opt 001 Ref Out, 4-51
options, 1-8
originate call
keys, 5-6
oscilloscope, 4-75
arming, 4-78
trigger level, 4-78
triggering, 4-78
oscilloscope test, 3-10
Other fusing, 1-3
Output Destination
CRT or Printer, 8-31
Output Heading comments, 8-31
Output Results
All or Failures, 8-30
Output RF Spectrum
Output RF Spectrum (Main View), 4-
83
output rf spectrum
cell control, 4-28
output RF spectrum measurement, 2-20
OutRFSpec
Output RF Spectrum (Trace View), 4-
85
P
Pages
Cell Control, 4-42
pages
call counts, 4-42
Paging
Cell Control, 4-42
Parallel Port
connector, 6-15
parameters
enter into Test Executive, 8-34
Parity, 8-6
Configure, 4-61
Pass Filter, A-12
Logging, A-12
Pause, A-11
PCN interface
connector, 6-15
Peak (Marker To)
Spectrum Analyzer (Marker Controls),
4-125
peak carrier power measurement, 2-14
Peak Phase Error
Phase/Freq (Main), 4-87
Phase/Freq (Multi-burst), 4-89
peak power
cell control, 4-28
peak transmitted power, 4-102
performance test software, 3-5
performance tests, 3-2
performance verification, 3-2
Personality, A-6, A-7
setting, A-6, A-7
phase and frequency
cell control, 4-28
phase error, 4-91
phase error measurement, 2-15
Pk TX Pwr
Pwr Ramp (Summary), 4-102
Pls Demod
Audio, 4-4, 4-75, 4-77, 4-80
Polarity
Phase/Freq (Data Bits), 4-94
POnOffFall
Pulse Fall, 4-110
POnOffRise
Pulse Rise, 4-108
Pos/Neg
Oscilloscope (Trigger Controls), 4-78
Position
Oscilloscope (Marker Controls), 4-81
Spectrum Analyzer (Marker Controls),
4-126
power
continuous wave, 4-55
power cord, 1-4
power meter
zeroing, 4-29, 4-55, 4-103
power ramp measurement, 2-16
power supply
configure to GPIB, 8-35
ppm, 4-14
PRBS, 4-42
PRBS Pattrn, 4-42
Pre-Trig
Oscilloscope (Trigger Controls), 4-78
previous
keys, 5-6
print
keys, 5-6
print address
selecting, 4-61
Print Adrs, 8-5
Configure, 4-61
Print Cancel
Configure, 4-61
Print Title
Configure, 4-61
Print To, 8-5
printer
configure to GPIB, 8-35
for showing test results, 8-31
options, 8-35
RS-232 or GPIB, 8-31
printer port
I/O configuration, 4-61
printouts
for the test results, 8-30
problem solving, 2-30
Procedure Files, 8-26
Procedure files, 8-2
Program Development Tools disk, 8-16
Program Example, 8-37
PROGram Interface Commands, 8-16
Program Listing Explanation, 8-40
program status
run indicators, 8-29
Program Structure, 8-37
programming techniques, 8-29
programs
IBASIC file structures, 8-29
protocol buffer, A-8
protocol error messages, 7-5
protocol interface connector, A-2
Protocol Interface Port, A-11
protocol messages, A-8
Protocol Monitor, A-11
protocol units, A-8